logo
خونه > محصولات >
ترکیب سیلیکونی
>
Fast Cure Potting Compound HN-8808F - 2-3 Hour Initial Set, Accelerate Production

Fast Cure Potting Compound HN-8808F - 2-3 Hour Initial Set, Accelerate Production

جزئیات محصول:
محل منبع: گوانگدونگ، چین
نام تجاری: Hanast
گواهی: ROHS
شماره مدل: HN-8808A/B
اطلاعات دقیق
محل منبع:
گوانگدونگ، چین
نام تجاری:
Hanast
گواهی:
ROHS
شماره مدل:
HN-8808A/B
عمر گلدان (25 درجه سانتیگراد):
20-30 دقیقه
زمان پخت اولیه (25 درجه سانتیگراد):
2-3 ساعت
زمان درمان کامل:
12-16 ساعت
نسبت مخلوط (A:B):
10: 1 (بر حسب وزن)
ویسکوزیته (مخلوط):
2500-3000 cP
سختی (ساحل A):
20-30 (GB/T531-1999)
هدایت حرارتی:
0.5±0.1 W/M·K (GB/T 38712-2020)
برجسته کردن:

High Light

برجسته کردن:

Fast cure silicone potting compound,HN-8808F potting compound 2-3 hour set,Accelerated production silicone potting material

,

HN-8808F potting compound 2-3 hour set

,

Accelerated production silicone potting material

اطلاعات تجاری
مقدار حداقل تعداد سفارش:
1 کیلوگرم
قیمت:
قابل مذاکره
جزئیات بسته بندی:
22 کیلوگرم / مجموعه (20 کیلوگرم A + 2 کیلوگرم B)؛ 11 کیلوگرم در ست (10 کیلوگرم A + 1 کیلوگرم B)
زمان تحویل:
5-7 روز
شرایط پرداخت:
T/T 、 پی پال
قابلیت ارائه:
50 تن در ماه
توضیحات محصول

Fast Cure Potting Compound HN-8808F - 2-3 Hour Initial Set, Accelerate Production

 

Fast Cure Potting Compound HN-8808F - 2-3 Hour Initial Set, Accelerate Production 0

 

Product Overview for Silicone Potting Compound:

For customers with high production efficiency demands, we offer the HN-8808F Fast-Cure version. It maintains the excellent physical and electrical properties of the HN-8808 series while significantly shortening the cure cycle. A 20-30 minute pot life meets most potting operation needs, achieving a handleable state in just 2-3 hours, allowing products to move quickly to the next process step. This greatly shortens production cycles and improves factory and equipment turnover.

 

Key Performance Parameters for Silicone Potting Compound:

* Pot Life (25°C): 20-30 minutes

* Initial Cure Time (25°C): 2-3 hours

* Full Cure Time: 12-16 hours

* Mix Ratio (A:B): 10 : 1 (by weight)

* Viscosity (Mixed): 2500-3000 cP

* Hardness (Shore A): 35-45 (GB/T531-1999)

* Thermal Conductivity: 0.5±0.1 W/M·K (GB/T 38712-2020)

* Dielectric Strength: ≥14 kV/mm

* All Other Electrical Properties: Consistent with standard HN-8808 series.

 

Fast Cure Potting Compound HN-8808F - 2-3 Hour Initial Set, Accelerate Production 1

 

Product Highlights for Silicone Potting Compound:

* Maximized Production Efficiency: Reduces initial cure time by over 50%, significantly speeding up the production line.

* Controllable Workflow: Predictable fast-cure characteristics enable precise production scheduling.

* Performance Not Compromised: Fast curing does not sacrifice protective properties, maintaining excellent insulation, thermal conductivity, and reliability.

* Reduces WIP Inventory: Faster curing reduces work-in-progress pile-up on the line.

* Ideal for Automation: Pairs perfectly with automated potting equipment for high-efficiency, rapid production.

 

Application Areas for Silicone Potting Compound:

* Mass production of consumer electronics

* High-volume potting of power tool controllers

* Automated production lines for power adapters

* Automotive tier-2 suppliers with strict takt time requirements

 

Fast Cure Potting Compound HN-8808F - 2-3 Hour Initial Set, Accelerate Production 2

 

Detailed Operating Guide for Silicone Potting Compound:

1. Production Preparation: Due to the shorter pot life, complete all prep work (PCB installation, housing positioning, tool setup) before starting to mix.

2. Precise Metering & Fast Mixing: Strongly recommend using a dual-component meter-mix machine with a static mixer to ensure uniform mixing within the short timeframe.

3. Efficient Degassing Process: Vacuum degassing time can be reduced to 1-2 minutes. For automated lines, consider dynamic degassing systems.

4. Rapid Potting: Dispense the mixed compound quickly to all products. Mix only enough compound for 5-10 minutes of potting at a time.

5. Line Design: The production line should have a defined staging area for initial curing after potting; products can be moved after 2-3 hours.

 

Key Precautions for Silicone Potting Compound:

* Not Suitable for Manual Work: Not recommended for manual mixing except for very small batches, as material starts reacting during mixing, leading to waste.

* Ambient Temperature Sensitivity: This grade is more sensitive to ambient temperature. Use in a temperature-controlled room (23±2°C) for best results.

* Do Not Heat Cure: Even though it's fast-cure, external heating is still strictly prohibited and will cause product failure.

* Batch Management: Practice "use immediately after mixing"; avoid gelation in pots or equipment.

 

Fast Cure Potting Compound HN-8808F - 2-3 Hour Initial Set, Accelerate Production 3

 

Packaging & Storage for Silicone Potting Compound:

* Standard Packaging: 22kg/set (20kg A + 2kg B); 11kg/set (10kg A + 1kg B). IBC totes also available for automated lines.

* Storage Conditions: Store in a cool, dry place. Ideal storage temperature: 10-25°C.

* Shelf Life: 6 months in original, unopened containers from date of manufacture.

 

Fast Cure Potting Compound HN-8808F - 2-3 Hour Initial Set, Accelerate Production 4

 

FAQ for Silicone Potting Compound:

1. Q: Is there a price difference between the fast-cure and standard versions?

A: Due to formulation adjustments, the fast-cure version is slightly higher priced. However, the production efficiency gains and cost savings will far outweigh the small material price difference.

2. Q: Can the pot life be made even shorter?

A: We can customize the cure speed based on your specific equipment and process requirements. Please provide details for our engineers to evaluate.

3. Q: Is the strength after initial cure (2-3 hours) sufficient for vibration testing?

A: It has some mechanical strength after initial cure, allowing gentle handling and testing. For harsh tests like vibration, we recommend testing after 16 hours (full cure).

4. Q: Can you provide process parameter suggestions for our potting machine?

A: Yes. Please tell us your equipment model, and we can provide initial machine setup parameters, including mix pressure, dispense speed, etc.

5. Q: If my product has a complex structure, will the fast-cure type have time to fill?

A: The 20-30 minute pot life is sufficient for most complex structures. For particularly tiny (<0.5mm) or high-aspect-ratio gaps, we can recommend a low-viscosity version of the fast-cure product.