
Product Selling Points
- 4.0 ± 0.5 W/m·K thermal conductivity with thermal resistance of ≤0.06 °C·in²/W at 80 °C and 50 psi, verified by ISO 22007-2 and ASTM D5470.
- Anti-sag, slump-resistant one-component gel: stays exactly where it is dispensed on vertical and overhead surfaces, with no pump-out or material migration during thermal cycling.
- Wide -40 to 150 °C working range with stable, repeatable thermal performance through aging, vibration and power-cycling tests.
- Ready-to-dispense single component: extrusion above 20 g/min from a 30CC tube at 0.6 MPa. No mixing, no pot life loss, no mixed-material waste — a direct drop-in for existing automatic dispensing lines.
- High electrical insulation: volume resistivity ≥1.0×1010 Ω·cm and dielectric breakdown >5 kV (ASTM D149), safe for use beside live ICs, IGBTs and power modules.
- Two delivery formats: semi-flowable gel for automated dispensing, or high-compression sheet form on request for gap-filling assembly.
- Export-ready compliance: RoHS 2.0, halogen-free and REACH compliant, matching OEM programs in Southeast Asia that ship to the EU and North America.
Product Introduction
HN-640AC-1 is a high-conductivity, anti-sag single-component thermal conductive gel for heat paths where 3 W/m·K materials are no longer enough. The 4.0 W/m·K filler system is combined with a controlled rheology that holds its shape after dispensing, so vertical and overhead gaps stay filled through assembly, transport and years of thermal cycling — without the pump-out that limits thermal grease.
The gel is supplied ready to use and needs no mixing, degassing or curing step on the line. It extrudes at more than 20 g/min from a 30CC tube at 0.6 MPa, which keeps it compatible with standard pneumatic dispensing, jetting and stencil-print processes already running in automotive electronics and IC assembly plants. Where a customer requires it, the same formulation can be supplied as a semi-flowable grade or as a high-compression sheet for manual gap-filling.
Electrically, HN-640AC-1 is a strong insulator: volume resistivity of at least 1.0×1010 Ω·cm and dielectric breakdown above 5 kV protect dense, low-clearance assemblies. It operates from -40 to 150 °C and meets RoHS 2.0, halogen-free and REACH requirements, which keeps finished modules compliant for export to Europe and North America.
Who This Is For
Factory owners and plant directors
One SKU covers ECU, ADAS, BMS, on-board charger and power-module heat paths, so fewer materials are carried on site and fewer lines need process qualification. Because the gel is single-component, there is no mixing station, no pot life to watch and no expired mixed batch to scrap. Supply capacity is around 50 tons per month, supported by RoHS 2.0, halogen-free and REACH documentation for export programmes.
Procurement teams
Evaluation can start from a single 30CC tube, then scale to 300ML cartridges for semi-automatic lines or 20KG pails for bulk automatic dispensing — no need to commit to a full drum during qualification. Stock items ship in 3-4 working days. Payment terms can be arranged around your existing supplier workflow (T/T, D/A, D/P).
Process and manufacturing engineers
The rheology is designed for standard dispensers: extrusion above 20 g/min at 0.6 MPa, anti-sag behaviour on vertical and overhead faces, and no curing oven in the flow. Thermal resistance of 0.06 °C·in²/W or lower is reached at 50 psi, so bond-line control is set by assembly torque rather than by material flow. Test methods are stated for every number (ISO 22007-2, ASTM D5470, D257, D149, D792) so results can be reproduced in your own lab.
Product managers and design owners
Where 800 V platforms, SiC modules or high-brightness LED arrays push power density up, one 4.0 W/m·K anti-sag gel can replace grease on some boards and gap pads on others, reducing part numbers and BOM complexity. The 0.1-2 mm working gap covers most die-to-heat-sink and housing interfaces, and the high-compression sheet option keeps the same chemistry where a solid format is preferred.
Typical Performance Data
| Property | Typical Value | Test Method |
| Model | HN-640AC-1 | / |
| Color | Light blue | Visual |
| Density | 3.1 ± 0.1 g/cm³ | ASTM D792 |
| Extrusion Rate | >20 g/min (30CC tube @ 0.6 MPa) | 30CC cartridge |
| Volume Resistivity | ≥1.0×1010 Ω·cm | ASTM D257 |
| Dielectric Breakdown Voltage | >5 kV | ASTM D149 |
| Operating Temperature Range | -40 to 150 °C | / |
| Thermal Conductivity | 4.0 ± 0.5 W/m·K | ISO 22007-2 |
| Thermal Resistance | ≤0.06 °C·in²/W (80 °C @ 50 psi) | ASTM D5470 |
| Shelf Life | 6 months at ≤25 °C, avoid compression and direct sunlight | / |
Core Application Scenarios

- Automotive electronics: ECU and ADAS controller housings, battery management system boards, on-board chargers, DC-DC converters and LED headlamp drivers, where vibration and vertical gaps rule out thermal grease.
- Integrated circuits and power modules: thermal interface between dies, IGBT, SiC and MOSFET power modules, heat spreaders and cold plates, including thin-bond-line gaps in dense packages.
- Network and communication equipment: base station RRUs, optical modules, switches and routers, where long service life without rework is required.
- Computing and high-performance processors: CPU, GPU and server modules with high power density and uneven contact surfaces.
- LED lighting: high-power COB and automotive LED modules bonded to aluminium or ceramic heat sinks.
- Consumer and industrial electronics: power supplies, inverters, motor drives and sensor packages requiring electrical insulation plus heat transfer.
How It Compares: Gel vs Grease vs Gap Pad
| Criteria | HN-640AC-1 one-component gel | Thermal grease | Thermal gap pad |
| Long-term pump-out | None: anti-sag structure holds position through cycling | Main failure mode on vertical and high-power joints | Not applicable |
| Vertical / overhead gaps | Stays in place after dispensing | Slumps and migrates | Needs mechanical compression |
| Gap range | 0.1-2 mm, conforms to surface roughness | Very thin bond line only | Fixed thickness, voids on rough surfaces |
| Production process | Dispense only, no mixing, no curing oven | Dispense or screen print, messy clean-up | Manual placement, higher labour content |
| Thermal performance | 4.0 W/m·K, ≤0.06 °C·in²/W at 80 °C / 50 psi | Low initially, degrades with pump-out | Depends heavily on mounting pressure |
| Electrical insulation | ≥1.0×1010 Ω·cm, >5 kV breakdown | Varies by filler system | Varies by formulation |
| Rework | Stays soft, allows mechanical separation | Requires cleaning of both surfaces | Replace with new pad |
Dispensing and Application Guide
- Clean the heat-sink and component surfaces, remove dust, grease and release agent, then dry completely.
- Fit the 30CC tube or 300ML cartridge with the nozzle that matches your bond-line width; for bulk pails use a pneumatic drum pump or automatic dispenser.
- Set dispensing pressure around 0.4-0.6 MPa and keep a continuous bead. The 4.0 W/m·K filler system is more highly filled than a 3 W/m·K grade, so allow a slightly larger nozzle and stable pressure for a smooth bead.
- Assemble the parts within the working time. No heating, curing or waiting step is required — the gel stays soft and tacky.
- Fasten to the designed torque. Bond-line thickness is controlled by compression (0.1-2 mm), and thermal resistance should be checked at the mounting pressure used in production.
- Clean nozzles and tools with alcohol before material residues set; once cured, mechanical removal is required.
Key Features

- One-component, no mixing and no pot life limit — zero mixed-material scrap.
- Anti-sag and slump-resistant: holds shape on vertical and overhead surfaces.
- 4.0 ± 0.5 W/m·K for high power density designs, with low thermal resistance at realistic mounting pressure.
- Excellent electrical insulation for dense, low-clearance assemblies.
- Reliable from -40 to 150 °C with strong aging and cycling stability.
- Compatible with pneumatic dispensing, jetting and stencil printing.
- Available as semi-flowable gel or high-compression sheet on request.
- RoHS 2.0, halogen-free and REACH compliant.
Industries Served
- Automotive electronics and electric vehicle powertrain manufacturing
- Semiconductor, IC packaging and power module assembly
- Telecommunications and data communication hardware
- Consumer electronics, computing and server hardware
- LED lighting and optoelectronics
- Industrial power electronics, drives and inverters
Packaging, Storage and Supply
- Packaging: 30CC tube for evaluation and small runs, 300ML cartridge for semi-automatic lines, 20KG pail for bulk automatic dispensing.
- Storage: dark place at 25 °C or below and 70% RH or below; avoid compression and direct sunlight.
- Shelf life: 6 months under the conditions above, 3 months outside them.
- Minimum order: from one 30CC tube for evaluation; production orders are normally placed in 20KG pails.
- Lead time: 3-4 working days for stock items; bulk quantities confirmed at order.
- Documentation: TDS, RoHS 2.0, halogen-free and REACH declarations supplied with the quotation.
Technical FAQ
- Does HN-640AC-1 need to be mixed or cured?
No. It is a single-component, ready-to-dispense gel. There is no A/B mixing, no pot life and no mixed-material waste. It is applied directly from the cartridge or pail.
- What is the difference between HN-640AC-1 and a 3 W/mK grade?
The 640 grade carries a higher filler loading for 4.0 W/mK instead of 3.0 W/mK, which suits higher power density joints. It is slightly denser (3.1 g/cm3) and slightly stiffer to dispense (>20 g/min instead of >30 g/min), so nozzle and pressure settings are adjusted accordingly.
- Will the gel flow out of a vertical gap?
No. The formulation is anti-sag and slump-resistant, so it stays where it is dispensed on vertical and overhead surfaces. Thermal cycling does not cause pump-out, which is the main failure mode of thermal grease in the same position.
- How is it applied in mass production?
With standard pneumatic dispensing equipment, jetting valves or stencil printing. Extrusion is above 20 g/min from a 30CC tube at 0.6 MPa, so existing lines can adopt it without equipment changes.
- Can it be used next to live or sensitive components?
Yes. Volume resistivity is at least 1.0×1010 Ω·cm and dielectric breakdown exceeds 5 kV (ASTM D149), so it provides electrical insulation as well as heat transfer.
- What gap thickness suits this product?
It performs best as a thin to medium gap filler between 0.1 mm and 2 mm. For thicker or more irregular gaps, we recommend a compression test with your actual surface finish and mounting pressure.
- What are the storage and shelf life requirements?
Store in a dark place at 25 °C or below and 70% RH or below, and avoid compression or direct sunlight. Shelf life is 6 months under these conditions and 3 months outside them.
- Which compliance standards does it meet?
RoHS 2.0, halogen-free and REACH. Certificates and test reports can be provided with the quotation.
- What is the minimum order and lead time?
Evaluation can start from a single 30CC tube. Production quantities are supplied in 300ML cartridges or 20KG pails, with 3-4 working days for stock items and bulk lead time confirmed at order.
- Do you support samples and technical evaluation for Southeast Asian customers?
Yes. We supply evaluation samples, dispensing parameter guidance and thermal test support, and we can work directly with your process engineers during line trials.