
Product Selling Points
- 2.0 ± 0.2 W/m·K thermal conductivity after cure, measured to ISO 22007-2, for battery pack, cold plate and computer heat paths.
- High electrical insulation: volume resistivity ≥1.0×1010 Ω·cm and dielectric breakdown above 5 kV (ASTM D149) protect densely packed cells, busbars and PCBs.
- Easy to dispense: low mixing resistance and extrusion above 15 g/min through a 15-element static mixer at 0.4 MPa — built for automatic 1:1 dispensing lines, not hand mixing.
- 1:1 mix ratio, room-temperature cure: more than 1 hour working time at 25 °C and full cure within 24 hours, with no oven required.
- Soft, flexible after cure: Shore 00 50 ± 10 absorbs vibration and thermal expansion stress between battery modules and cold plates.
- UL94 V-0 flame rating and a -40 to 150 °C working range for safety-critical battery and power electronics assemblies.
- RoHS 2.0, halogen-free and REACH compliant, matching export programmes in Southeast Asia that ship to the EU and North America.
Product Introduction
HN-NJ200-2 is a two-component, 1:1 room-temperature curing thermal conductive gel for interfaces where heat must cross from a live assembly into a metal cold plate or housing. After mixing, it flows into the gap, wets both surfaces and cures into a soft, flexible rubber with a thermal conductivity of 2.0 W/m·K, so it fills air voids that would otherwise dominate the thermal path.
The formulation is designed around automatic dispensing: low mixing resistance, an extrusion rate above 15 g/min through a 15-element static mixer at 0.4 MPa, and a working time of more than one hour at 25 °C. That window is long enough for multi-point dispensing on a battery module or a server chassis, while full cure is still reached within 24 hours at room temperature — no curing oven, no reflow step, no thermal excursion on the cells.
Electrically, the cured gel is a strong insulator: volume resistivity at or above 1.0×1010 Ω·cm and dielectric breakdown above 5 kV. Combined with UL94 V-0 flame performance, a -40 to 150 °C range and RoHS 2.0 / halogen-free / REACH compliance, it fits battery packs and computer hardware that must pass both safety and export requirements.
Who This Is For
Factory owners and plant directors
One material covers battery pack potting, cold plate interfaces and computer chassis heat paths, so fewer part numbers are carried and fewer processes need qualification. Room-temperature cure removes the oven from the line: lower energy cost, shorter cycle time, and no heat exposure to cells or finished boards. Production capacity is around 50 tons per month, with RoHS 2.0, halogen-free and REACH documentation available for export orders.

Procurement teams
Evaluation starts from a 1 kg kit (0.5 kg A + 0.5 kg B), then scales to 10 kg kits or 20 kg sets for production. Stock items ship in 3-4 working days, and payment terms can follow your existing supplier workflow (T/T, D/A, D/P). Shelf life is 6 months below 40 °C, so kit sizes can be matched to your consumption rate without write-offs.
Process and manufacturing engineers
The 1:1 ratio is volume-tolerant, the pot life exceeds one hour at 25 °C so a static mixer does not clog mid-run, and extrusion stays above 15 g/min at 0.4 MPa. Cure is complete within 24 hours at room temperature and can be accelerated to suit your takt time. Every number in the data table carries its test method (ISO 22007-2, ASTM D2240, D257, D149, D792), so results can be reproduced in your own lab before line adoption.
Product managers and design owners
For 48 V and 96 V battery packs, cold plate assemblies and fanless computer enclosures, this grade replaces both gap pads and potting compound: it fills irregular gaps, stays soft under thermal cycling, and bonds nothing permanently, so service and rework remain possible. Its 2.0 W/m·K rating and V-0 rating cover the majority of mid-power designs without moving to a specialist high-conductivity grade.
Typical Performance Data
| Property | Typical Value | Test Method |
| Model | HN-NJ200-2 | / |
| Color (Component A / B) | Gray / White | Visual |
| Mix Ratio | 1:1 | / |
| Density | 2.8 ± 0.1 g/cm³ | ASTM D792 |
| Hardness After Cure | Shore 00 50 ± 10 | ASTM D2240 |
| Working Time (25 °C) | >1 hour (time for viscosity to double) | / |
| Cure Time (25 °C) | <24 hours (adjustable on request) | / |
| Extrusion Rate | >15 g/min (0.4 MPa, 15-element static mixer) | / |
| Volume Resistivity | ≥1.0×1010 Ω·cm | ASTM D257 |
| Dielectric Breakdown Voltage | >5 kV | ASTM D149 |
| Operating Temperature Range | -40 to 150 °C | / |
| Flame Rating | V-0 | UL94 |
| Thermal Conductivity | 2.0 ± 0.2 W/m·K | ISO 22007-2 |
| Shelf Life | 6 months below 40 °C, avoid direct sunlight | / |
Core Application Scenarios

- Battery packs and cold plates: gap filling between prismatic or cylindrical cells and liquid-cooling cold plates, module-to-housing interfaces and busbar encapsulation, where soft cure absorbs swelling and vibration.
- Computer industry: server and workstation CPU/GPU modules, fanless industrial PCs, power supply and SSD heat spreaders, and chassis-to-heat-sink interfaces on uneven surfaces.
- Integrated circuits and power modules: IGBT and MOSFET module baseplates, inverters and motor controllers requiring electrical insulation plus heat transfer.
- Network and communication equipment: base station RRUs, optical modules, switches and routers built for long service life.
- Automotive electronics: on-board chargers, DC-DC converters, ECU housings and LED drivers exposed to vibration and thermal cycling.
- LED lighting: high-power COB modules bonded to aluminium and ceramic heat sinks.
How It Compares: Two-Component vs One-Component vs Gap Pad
| Criteria | HN-NJ200-2 two-component gel | One-component gel | Thermal gap pad |
| Cure behaviour | 1:1 mix, room-temperature cure in under 24 h, flexible rubber | Stays paste-like, no cure | Pre-cured sheet |
| Gap and surface conformity | Fills irregular gaps and wets rough surfaces before cure | Fills gaps but can migrate under pressure | Fixed thickness, leaves voids on rough faces |
| Mechanical stress | Shore 00 50 absorbs vibration and cell swelling | No mechanical coupling | Low, but requires high mounting pressure |
| Production process | Automatic 1:1 dispensing with static mixer, no oven | Dispense only | Manual placement, higher labour |
| Rework and service | Soft rubber, mechanically separable | Smears and migrates | Replace with new pad |
| Best fit | Battery packs, cold plates, structural housings | Thin interfaces, quick assembly | Large flat gaps, hand assembly |
Mixing, Dispensing and Curing Guide
- Bring both components to workshop temperature (20-30 °C) and check that the A and B containers are within shelf life before opening.
- Fit a 15-element static mixer to the 1:1 cartridge or meter-mix pump; purge the first 20-30 mm of mixed material to waste to guarantee a correct ratio.
- Dispense in a continuous bead or serpentine pattern, keeping the nozzle submerged in the bead to avoid air entrapment. Extrusion runs above 15 g/min at 0.4 MPa.
- Assemble the parts within the working time (more than 1 hour at 25 °C); the gel conforms to both surfaces and displaces air as it is compressed.
- Leave to cure at room temperature for up to 24 hours, or accelerate with mild heat where the assembly allows. Do not disturb the joint until the gel has set.
- Clean nozzles and tools with alcohol before the mixed material cures; once cured, remove mechanically.
Key Features
- Two-component, 1:1 mix ratio for meter-mix and cartridge dispensing.
- 2.0 ± 0.2 W/m·K after cure with good surface wetting.
- High electrical insulation with >5 kV dielectric breakdown.
- Easy dispensing: low mixing resistance, >15 g/min through a static mixer.
- Room-temperature cure in under 24 hours, no oven.
- Soft Shore 00 50 ± 10 rubber absorbs vibration and thermal expansion.
- UL94 V-0 flame rating and -40 to 150 °C service range.
- RoHS 2.0, halogen-free and REACH compliant.
Industries Served
- Battery pack and energy storage manufacturing
- Computer, server and data centre hardware
- Semiconductor, IC packaging and power module assembly
- Telecommunications and data communication equipment
- Automotive electronics and electric vehicle components
- LED lighting and industrial power electronics
Packaging, Storage and Supply
- Packaging: 1 kg kit (0.5 kg A + 0.5 kg B) for evaluation, 10 kg kit for pilot runs, 20 kg set (10 kg A + 10 kg B) for production.
- Storage: dark place at 25 °C or below, 70% RH or below, away from direct sunlight.
- Shelf life: 6 months below 40 °C; 3 months outside the recommended conditions.
- Minimum order: one 1 kg kit for evaluation.
- Lead time: 3-4 working days for stock items; bulk quantities confirmed at order.
- Documentation: TDS, RoHS 2.0, halogen-free, REACH and UL94 V-0 test report supplied with the quotation.
Technical FAQ
- What is the mix ratio and how should it be dispensed?
The ratio is 1:1 by component. Use a meter-mix pump or a 1:1 cartridge with a 15-element static mixer. Purge the first 20-30 mm of mixed material so the ratio is correct from the start of the bead.
- How long do I have after mixing?
Working time at 25 °C is more than one hour, defined as the time for viscosity to double. In practice a static mixer stays usable through a normal production run; change the mixer if the line stops for a long period.
- Does it need an oven to cure?
No. Full cure is reached within 24 hours at room temperature. If your takt time requires it, the cure schedule can be adjusted and we will recommend parameters for your assembly.
- Why choose a curing gel instead of a non-curing one?
A curing gel forms a soft rubber that does not migrate and mechanically couples the battery module or board to the cold plate, which helps with vibration and cell swelling. A non-curing gel stays paste-like and needs a mechanical gap control.
- Is the cured gel safe near live electronics?
Yes. Volume resistivity is at least 1.0×1010 Ω·cm and dielectric breakdown exceeds 5 kV (ASTM D149).
- What gap thickness is suitable?
It is typically used from 0.2 mm to 3 mm. For thicker sections or unusual geometries, share the drawing and we will advise on bead pattern and fill volume.
- Will the soft rubber take the load of a battery module?
Shore 00 50 ± 10 provides cushioning rather than structural support. Load-bearing functions should be handled by the mechanical design, with the gel acting as the thermal and vibration interface.
- What are the storage and shelf life requirements?
Store below 40 °C in a dark place, avoid direct sunlight. Shelf life is 6 months under these conditions and about 3 months outside them. Do not freeze.
- Which compliance and safety standards are met?
RoHS 2.0, halogen-free and REACH, with a UL94 V-0 flame rating. Test reports can be provided with the quotation.
- Do you support samples and line trials for Southeast Asian customers?
Yes. We supply 1 kg evaluation kits, dispensing parameter guidance and thermal test support, and can work with your process engineers during line trials.