Low Viscosity 1:1 Thermal Conductivity Potting Glue Two-Component Silicone Potting Compound for Electronic Components Circuit Board Connector
Features of RTV Silicone Potting Compound:
Flexible silicone glue
Low shrinkage rate, no corrosion of components after curing.
Flame retardant, high and low -temperature resistance from -50ºC to 250ºC (58°F to 432°F).
Excellent electrical properties and Thermal conductivity.
* Color: Grey, white, black
Product description of RTV Silicone Potting Compound
HN-8806, two-component addition type silicone potting rubber which can be cured into high-performance elastomer by room temperature or heating.
Technical Parameters of of RTV Silicone Potting Compound:
| | Test Items | Test Standard | Units | Product test results |
| Part A | Part B |
Before Curing | 1 | Appearance | By eyes | --- | Grey, fluid | White, fluid |
| 2 | Viscosity | GB/T10247- 2008 | 25ºC,mPa·S | 4500~5000 | 4500~5000 |
| 3 | Density | GB/T 13354-92 | 25ºC,g/cm3 | 1.50±0.05 | 1.50±0.05 |
| 4 | Mixing Ratio (A : B) | 1:1 | Weight ratio | 100 | 100 |
| Volume ratio | 100 | 100 |
| 5 | Operating time | Measured | hr | 0.3-0.4 |
| 6 | Curing condition | Measured | hr | 4~12 (25ºC, initial cure) |
0.20 (80ºC) |
After Curing | 7 | Appearance | By eyes | --- | Grey Elastomer |
| 8 | Hardness | GB/T 531.1-2008 | Shore A | 50±5 |
| 9 | Thermal conductivity | GB/T10297-1998 | w/m·k | ≥0.76 |
| 10 | Expansivity | GB/T20673-2006 | µm/(m,ºC) | 210 |
| 11 | Moisture Absorption | GB/T 8810-2005 | 24h,25ºC,% | 0.01~0.02 |
| 12 | Volume resistivity | GB/T 1692-92 | (DC500V),Ω· cm | 1.0×1016 |
| 13 | Dielectric intensity | GB/T 1693-2007 | Kv/mm(25ºC) | 18~25 |
| 14 | Temperature Resistance | Measured | ºC | -50~+250 |
* UV-94 Fire retardant: After two times 10s burn tests on a 3mm-thick sample, the flame was extinguished within 30s, and no burnt fell. [1]
* Noted: The data after curing are all measured after the silicone is completely cured.
Application of RTV silicone potting compound
HOW TO USE of RTV Silicone Potting Compound
1. When used, weigh A and B according to proportion and then mix them evenly.
Mix thoroughly and evenly with a clean stirring device in a clean container, and then potting can be done.
It can also be sealed under a vacuum after removing the bubbles.
2. The surface of the potting element needs to be cleaned.
If the potting product is too large, it is recommended to potting in stages and then cure at room temperature (4-12hr) or by heating (80ºC-0.5hr).
3. For the automatic potting production line, in order to ensure accurate mixing ratio of A and B, Part A and Part B should be vacuumed respectively to remove the bubbles (the foaming time is 5-10 minutes), and then A and B should be pumped to the static mixer in proportion with a metering pump, and then potting can be done after mixing evenly.
- Storage and transportation:
This product is non-toxic non-dangerous goods, according to the general chemical handling, stored in a cool & dry place (room temperature).
- Shelf Life: 6 months, overdue please reinspect; If it meets the standard, it can still be used.
About us
Your message must be between 20-3,000 characters!
english
français
Deutsch
Italiano
Русский
Español
português
Nederlandse
ελληνικά
日本語
한국
العربية
हिन्दी
Türkçe
indonesia
tiếng Việt
ไทย
বাংলা
فارسی
polski
Overall Rating
Rating Snapshot
The following is the distribution of all ratingsAll Reviews