Two-Component RTV Potting Silicone Rubber Electrical Insulation Silicone Potting Compound High Thermal Conductivity For Battery Pack Adapter Led Driver
PRODUCT DESCRIPTION of RTV Potting Silicone Rubber
HN-8806, two-components addition type silicone potting rubber which can be cured into high-performance elastomer by room temperature or heating.
Its good thermal conductivity function can effectively transfer the heat emitted by the electronic components.
Application of RTV Potting Silicone Rubber
This product is widely used in the potting and sealing of electronic components, such as various power modules, circuit boards, high-voltage transformers, battery packs, fast-charging adapters
Silicone potting compounds are indispensable key materials in the electronics industry and high-end manufacturing. Their core functions include protection, insulation, heat dissipation, and support. Their applications extend to almost all areas requiring circuit protection and environmental sealing.
Technical Parameters of RTV Potting Silicone Rubber
| Test Items |
Test Standard |
Units |
Product test results |
| Part A |
Part B |
|
Before
Curing
|
1 |
Appearance |
By eyes |
--- |
Grey, fluid |
White, fluid |
| 2 |
Viscosity |
GB/T10247- 2008 |
25ºC,mPa·S |
4500~5000 |
4500~5000 |
| 3 |
Density |
GB/T 13354-92 |
25ºC,g/cm3 |
1.50±0.05 |
1.50±0.05 |
| 4 |
Mixing Ratio (A : B) |
1:1 |
Weight ratio |
100 |
100 |
| Volume ratio |
100 |
100 |
| 5 |
Operating time |
Measured |
hr |
0.3-0.4 |
| 6 |
Curing condition |
Measured |
hr |
4~12
(25ºC, initial cure)
|
|
0.20
(80ºC)
|
|
After
Curing
|
7 |
Appearance |
By eyes |
--- |
Grey Elastomer |
| 8 |
Hardness |
GB/T 531.1-2008 |
Shore A |
50±5 |
| 9 |
Thermal conductivity |
GB/T10297-1998 |
w/m·k |
≥0.76 |
| 10 |
Expansivity |
GB/T20673-2006 |
µm/(m,ºC) |
210 |
| 11 |
Moisture Absorption |
GB/T 8810-2005 |
24h,25ºC,% |
0.01~0.02 |
| 12 |
Volume resistivity |
GB/T 1692-92 |
(DC500V),Ω· cm |
1.0×1016 |
| 13 |
Dielectric intensity |
GB/T 1693-2007 |
Kv/mm(25ºC) |
18~25 |
| 14 |
Temperature Resistance |
Measured |
ºC |
-50~+250 |
How to use RTV Potting Silicone Rubber
1. When used, mix A and B components evenly, and then weigh A and B components according to proportion. Mix thoroughly and evenly with a clean stirring device in a clean container, and then potting can be done. It can also be sealed under a vacuum after removing the bubbles. 2. The surface of the potting element needs to be cleaned. If the potting product is too large, it is recommended to potting in stages and then cure at room temperature (4-12hr) or by heating (80ºC-0.5hr). 3. For the automatic potting production line, in order to ensure accurate mixing ratio of A and B, Part A and Part B should be vacuumed respectively to remove the bubbles (the foaming time is 5-10 minutes), and then A and B should be pumped to the static mixer in proportion with a metering pump, and then potting can be done after mixing evenly.
About us
Your message must be between 20-3,000 characters!
