HN100 1.0 W/mK Low Oil Bleed Thermal Grease Paste – 200°C High Temperature Stable Silicone Compound
HN100 is a single-component, non-curing thermal grease paste (also known as thermal compound, thermal conductive grease, heat sink compound, heat sink grease, thermal joint compound, thermal coupling grease, thermal interface material / TIM) built on a high-purity silicone oil (polydimethylsiloxane / PDMS) base with an inorganic ceramic (metal oxide) thermally conductive filler system. It delivers 1.0 ± 0.1 W/m·K thermal conductivity, keeps a stable paste consistency from -50°C to +200°C, and stays paste-like instead of drying out, so the thermal interface does not degrade after long-term service. The compound combines electrical insulation with low oil bleed, low volatility, near-zero free radical content and resistance to water, ozone and weathering. It is non-toxic, odorless (odourless), non-corrosive and compliant with RoHS 2.0 and REACH, making it suitable for continuous-duty electronics and power assemblies.
Why Choose This Thermal Grease
- Stable 1.0 ± 0.1 W/m·K thermal conductivity (ASTM D5470) – a reliable heat transfer compound for CPU, GPU, power module and heat sink interfaces where repeatable thermal performance matters more than headline numbers.
- Low oil bleed (oil separation ≤ 0.3%) and low volatility (≤ 0.6%) at 200°C / 24 h – the interface stays clean, so pump-out and dry-out risk is controlled in vertically mounted, high-vibration and long-duty assemblies.
- 200°C 8-day no powdering, 280°C 3-hour no drying (0.2 mm film) – validated high temperature stability gives engineering and procurement teams documented evidence for thermal cycling and thermal shock reviews.
- Non-curing – will never dry, never harden – the paste keeps its consistency indefinitely, which simplifies rework, re-seating and field repair of heat sinks.
- Near-zero free radical content – reduces oxidation and embrittlement of the silicone matrix, supporting long service life under continuous heat and UV / ozone / weathering exposure.
- Non-corrosive formula – safe for aluminium, copper, nickel and sensitive electronic substrates, preventing galvanic corrosion and surface damage.
- Excellent dielectric strength – 2450 V/mm breakdown voltage at 0.20 mm (IEC 60243) – one paste provides both heat transfer and electrical insulation for power modules that need dielectric isolation.
- Water and humidity resistant – resistant to water, moisture, ozone and weathering, with good damp heat performance and effectively waterproof inside sealed enclosures and industrial cabinets.
- High workability – penetration 370 ± 20 (1/10 mm) supports brushing, rolling, stencil printing, screen printing and automatic dispensing on manual and automated lines, with thixotropic flow that holds the printed pattern.
- Low thermal resistance, thin bond line thickness (BLT) friendly – low viscosity and good wetting allow a very thin gap fill, keeping interface thermal resistance and thermal impedance low without pumping out.
Technical Data
| Property | Test Method / Condition | Unit | Value |
| Appearance | Visual inspection | — | White or grey paste |
| Thermal Conductivity | ASTM D5470 | W/m·K | 1.0 ± 0.1 |
| Specific Gravity | GB/T 13354-1992 / 25°C | g/cm³ | 1.85 ± 0.08 |
| Oil Separation (Oil Bleed) | SH/T 0324-1992 / 200°C, 24 h | % | ≤ 0.3 |
| Volatile Matter | SH/T 0337-92 / 200°C, 24 h | % | ≤ 0.6 |
| Penetration (Cone Penetration) | GB/T 269-2023 / 25°C | 1/10 mm | 370 ± 20 |
| High-Temperature Stability | 200°C constant-temperature oven, 0.2 mm film | — | No powdering after 8 days continuous baking |
| Temperature Resistance | Heating platform, 280°C, 0.2 mm film | — | No drying after 3 h continuous baking |
| Breakdown Voltage | IEC 60243 / 0.20 mm thickness | V/mm | 2450 |
| Operating Temperature Range | — | °C | -50 to +200 |
All values are measured under standard conditions and are for reference only. Actual thermal performance may vary with application conditions, bond line thickness (BLT) and contact pressure.
Applications
The paste is used as a thermal interface between heat-generating components and heat-dissipation components in electronic and electrical equipment, and covers a wide range of production and repair scenarios:
- Computing and servers: CPU assemblies, GPU and graphics cards, notebook and desktop cooling, server and data center heat sinks.
- Power electronics: power transistors, thyristors, IGBT and MOSFET modules, voltage regulators, power modules, rectifiers and regulated power supply units.
- Telecom and 5G: base station units, microwave communication systems, microwave transmission equipment and telecom power supplies.
- Automotive and EV: automotive electronics, automotive refrigerators, EV battery cooling plates and on-board chargers (OBC), where a non-curing, oil-bleed-controlled thermal compound is preferred.
- Lighting and appliances: LED lighting fixtures, LED drivers, printer heads, temperature sensors and thermistors.
- Repair and refurbishment: EMS and service centers replacing dried-out factory paste with a re-workable heat sink grease.
Application Instructions
- Surface preparation: clean all contact surfaces with a solvent to remove old grease, dust and oxidation; make sure the surfaces are completely dry.
- Application: apply the thermal grease directly by brushing, rolling, automatic dispensing, stencil or screen printing.
- Spreading: transfer a small amount with a clean tool (razor blade, plastic spatula or clean knife) and spread evenly to the required thickness.
- Thickness control: the thinner the layer, the better the heat transfer; excess paste does not improve performance and may reduce efficiency, so wipe the edges with a lint-free cloth.
- Assembly: assemble the heat sink and heat source immediately and torque the fasteners to specification to keep a uniform bond line thickness.
Packaging, Supply and Customization
- Standard packaging: 1 kg drum and 5 kg drum; pail, bulk container and private label packaging available on request.
- Flexible filling: syringe, cartridge and tube filling for production lines and retail-ready private label programs.
- MOQ: 1 kg for standard grades, so trial orders and small batch builds are supported before volume ramp-up.
- Supply capability: 50 tons per month from our own factory, with 3-5 working days lead time for standard drums and fast delivery for repeat orders.
- OEM / ODM: custom formulation (thermal conductivity, viscosity, colour, filler loading), custom packaging and private label available for brand owners and thermal solution providers.
- Payment terms: T/T, L/C and Western Union.
Compliance and Documents
- RoHS 2.0 and REACH compliant; non-toxic, odourless and non-corrosive.
- TDS, MSDS and COA are available on request (datasheet download link provided on inquiry), together with test reports for thermal conductivity, oil separation and dielectric strength to support your incoming inspection and customer audit.
- Transportation is classified as non-dangerous goods (general chemicals).
Storage and Shelf Life
- Store in the original, tightly sealed container in a cool, dry, well-ventilated area, protected from direct sunlight; recommended storage temperature below 27°C.
- Shelf life: 12 months from the date of manufacture when stored unopened and properly sealed, with good storage stability and no settlement problems.
- A small amount of silicone oil may separate during storage; this is normal, does not affect performance and can be stirred before use.
FAQ
Is this a thermal paste or a thermal compound? They are the same product family: a thermal paste, thermal compound, heat sink compound, heat sink grease or thermal joint compound used as a thermal interface material (TIM) between a heat source and a heat sink.
Will it dry out or pump out over time? No. HN100 is non-curing and never dries or hardens; oil separation is ≤ 0.3% at 200°C / 24 h, which keeps pump-out under control in vertical and high-vibration assemblies.
Is it electrically insulating? Yes. Breakdown voltage is 2450 V/mm at 0.20 mm thickness (IEC 60243), so it works as a dielectric heat transfer compound for power modules and power supplies.
Can it be used outdoors or in humid environments? Yes. The compound is water resistant and resistant to moisture, humidity, ozone and weathering, and passes 200°C 8-day no-powdering aging at 0.2 mm film.
Can you supply OEM, private label or a custom formulation? Yes. As a manufacturer we support OEM / ODM projects, custom thermal conductivity and viscosity, private label packaging and bulk wholesale supply of 50 tons per month.
What is the MOQ, lead time and sample policy? MOQ starts at 1 kg, standard drums ship in 3-5 working days, and free samples with TDS and MSDS are available for evaluation.