HN100 is a single-component, non-curing thermally conductive silicone grease that combines 1.0 ± 0.1 W/m·K thermal conductivity (ASTM D5470) with strong electrical insulation: 2450 V/mm breakdown voltage at 0.20 mm. It is a white or grey paste with low viscosity and 370 ± 20 (1/10 mm) penetration, so it wets rough castings and stamped heat sinks easily, spreads to a thin film by hand, brush, roller, screen printing or automatic dispensing, and never hardens or cures in service.
The defining property of HN100 is long-duration heat stability. In a 200 °C constant-temperature oven a 0.2 mm film shows no powdering after 8 days of continuous baking, and on a 280 °C heating platform a 0.2 mm film shows no drying after 3 hours. For power supplies, transformers, relays, heating elements and appliance control boards that run hot for years, that behaviour means the interface stays soft and conductive instead of turning into an insulating crust.
HN100 is supplied to B2B factories in Vietnam, Thailand, Indonesia, Malaysia and the Philippines as non-dangerous goods in 1 kg and 5 kg plastic drums, with TDS, MSDS and a COA for every lot, which keeps import clearance, warehouse storage and supplier audits straightforward in hot and humid climates.
![]()
A thermal interface is approved by different people for different reasons. HN100 is documented so each function can sign off from its own angle.
Fewer field failures and less rework: a non-curing paste that survives 200 °C for 8 days without powdering removes the dry-out failure mode behind returned power supplies and burnt appliance boards, and one source factory covers grease, gel and potting compound for the same product.
Simple commercial terms: minimum order from 1 kg, 3 to 5 working days for stock drums, TDS and MSDS for customs, COA per lot, non-dangerous goods classification with no DG surcharge, and private label drums for your own brand.
Design data that holds up: 1.0 ± 0.1 W/m·K, 2450 V/mm dielectric strength for creepage and clearance margins, 1.85 ± 0.08 g/cm³ low density, 370 ± 20 penetration for wet-out on rough surfaces, and oil separation ≤ 0.3% with volatiles ≤ 0.6% at 200 °C / 24 h to limit pump-out.
Fast qualification: 1 kg trial drums for the first build, 7 to 15 days for custom viscosity, colour or private label, and direct access to our Shenzhen application engineers for bond line thickness, dispensing and reliability test planning.
One approved supplier across the range: the same silicone grease platform runs from 1.0 to 6.0 W/m·K plus insulating and high-conductivity grades, so several product lines and OEM or ODM programmes can share one material approval.
| Property | Test Method / Condition | Unit | Value |
|---|---|---|---|
| Appearance | Visual inspection | — | White or grey paste |
| Thermal Conductivity | ASTM D5470 | W/m·K | 1.0 ± 0.1 |
| Specific Gravity | GB/T 13354-1992 / 25 °C | g/cm³ | 1.85 ± 0.08 |
| Oil Separation (Oil Bleed) | SH/T 0324-1992 / 200 °C, 24 h | % | ≤ 0.3 |
| Volatile Matter | SH/T 0337-92 / 200 °C, 24 h | % | ≤ 0.6 |
| Penetration (Cone Penetration) | GB/T 269-2023 / 25 °C | 1/10 mm | 370 ± 20 |
| High-Temperature Stability | 200 °C constant-temperature oven, 0.2 mm film | — | No powdering after 8 days continuous baking |
| Temperature Resistance | Heating platform, 280 °C, 0.2 mm film | — | No drying after 3 h continuous baking |
| Breakdown Voltage | IEC 60243 / 0.20 mm thickness | V/mm | 2450 |
| Operating Temperature Range | — | °C | -50 to +200 |
| Curing Behaviour | — | — | Single component, non-curing |
| Compliance | — | — | RoHS 2.0 |
All values are measured under standard conditions and are for reference only. Actual thermal performance varies with application conditions, bond line thickness and contact pressure.
![]()
HN100 is specified wherever a thin, electrically insulating and heat stable interface is needed between a heat generating component and a heat sink, housing or heat strip.
Power supplies, transformers and industrial controlBecause HN100 is soft (370 ± 20 penetration) and insulating, it wets rough castings well. Use the thinnest film that still gives full contact, and validate on your own assembly.
| Interface | Typical starting BLT | Recommended method |
|---|---|---|
| Power supply, relay, thermal switch | 0.05 to 0.10 mm | Brush, syringe or stencil printing |
| Transformer, reactor, power resistor | 0.10 to 0.20 mm | Roller, brush or cartridge dispensing |
| Cast or machined heat sink, rough surface | 0.15 to 0.30 mm | Roller or automatic dispensing with clamping |
| EV charger and appliance control board | 0.08 to 0.15 mm | Stencil, screen printing or automatic dispensing |
| Item | Detail |
|---|---|
| Standard packaging | 1 kg plastic drum, 5 kg plastic drum |
| Custom packaging | Available on request: syringe, cartridge, larger drums, private label |
| Minimum order quantity | 1 kg (trial drum for NPI and sample evaluation) |
| Delivery time | 3 to 5 working days for stock drums; 7 to 15 days for custom formulation or private label |
| Supply ability | 50 tons per month |
| Payment terms | T/T, L/C |
| Shelf life | 12 months from date of manufacture, unopened and sealed |
| Storage | Below 27 °C, cool, dry, ventilated area, out of direct sunlight, container tightly sealed |
Slight oil separation during storage is normal for a non-curing silicone grease and does not affect performance; stir thoroughly before use. Keep containers sealed when not in use and store away from food, children and incompatible materials.
HN100 is tested for long-duration heat exposure, not only for conductivity. In a 200 °C constant-temperature oven a 0.2 mm film shows no powdering after 8 days of continuous baking, and on a 280 °C heating platform a 0.2 mm film shows no drying after 3 hours. Because the grease is non-curing, the interface stays soft instead of crusting over, which is the usual failure mode in power supplies, transformers and heating appliances.
Yes. HN100 has a breakdown voltage of 2450 V/mm at 0.20 mm thickness tested to IEC 60243, so it provides a useful insulation margin in power supplies, relays, thermal switches and BMS boards. Insulation depends on the actual film thickness and on your mechanical design, so confirm creepage and clearance distances against your own safety standard and keep the bond line uniform.
HN100 is used on power supply and transformer heat sinks, relays, solid state relays, thermal switches, power resistors, heating elements and hot plates, home appliance and induction cooker control boards, LED drivers, EV chargers, OBC, BMS and battery modules, energy storage cabinets, PV inverters, servers, 5G telecom equipment, microwave devices, printer heads, temperature sensors and automotive electronics including car refrigerators.
Yes. We regularly ship HN100 to Vietnam, Thailand, Indonesia, Malaysia and the Philippines and to other Southeast Asian destinations on request. It is classified as non-dangerous goods, so there is no dangerous goods surcharge, and it travels in 1 kg or 5 kg plastic drums on pallets. Every lot ships with a TDS, an MSDS and a COA, and private label drums are available for OEM and ODM customers.
The minimum order is 1 kg, which is enough for a line trial or engineering evaluation. Stock drums ship in 3 to 5 working days, while custom viscosity, colour or private label packaging takes 7 to 15 days. Supply capacity is 50 tons per month with T/T or L/C payment terms, shelf life is 12 months below 27 °C, and a REACH declaration is available on request.
Shenzhen Hanast New Materials Co., Ltd. is a China-based source factory for RTV-2 liquid silicone, potting compounds and thermal interface materials. Established in 2010 with a 40,000 m² production base, the company is an export-driven manufacturer with 70% to 80% of its business overseas, serving B2B clients that include ABB, Apple, Foxconn and BYD with OEM and ODM encapsulation and thermal management solutions.
Our thermal range covers silicone grease from 1.0 to 6.0 W/m·K, including insulating, high conductivity and high temperature grades, plus thermally conductive potting compounds and silicone gels. Because grease, gel and potting compound for the same assembly come from one factory, your engineering team works with one technical contact and your purchasing team consolidates one supplier, one documentation set and one shipment schedule.
![]()
Send your heat sink drawing or power supply specification and our application engineers will recommend the right grade and bond line thickness, and arrange a 1 kg sample drum for your trial build.