Home > Products >
Thermal Grease Paste
>
1.0 W/mK Non-Curing Thermal Grease with 2450 V/mm Dielectric Strength for Heat Sink Assembly

1.0 W/mK Non-Curing Thermal Grease with 2450 V/mm Dielectric Strength for Heat Sink Assembly

Product Details:
Place of Origin: Shenzhen, Guangdong, China
Brand Name: HANAST
Certification: RoHS 2.0
Model Number: HN100
Detail Information
Place of Origin:
Shenzhen, Guangdong, China
Brand Name:
HANAST
Certification:
RoHS 2.0
Model Number:
HN100
Thermal Conductivity:
1.0 ± 0.1 W/m·K
Dielectric Strength:
2450 V/mm At 0.20 Mm
Specific Gravity:
1.85 ± 0.08 G/cm³ At 25 °C
Penetration:
370 ± 20 (1/10 Mm) At 25 °C
Operating Temperature:
−50 °C To +200 °C
Oil Separation:
≤ 0.3 % (200 °C, 24 H)
Highlight:

High Light

Highlight:

Supplier Audit Ready Thermal Grease

,

Batch COA And Dual Source Paste

,

Southeast Asia Contract Manufacturer Supply

Trading Information
Minimum Order Quantity:
1 kg
Packaging Details:
1 kg and 5 kg plastic drums, custom pack sizes on request
Delivery Time:
7 to 15 days
Payment Terms:
T/T,L/C
Supply Ability:
50 tons per month
Product Description
HN100 1.0 W/mK insulating thermal grease, packaged for supplier audit and dual sourcing

HN100 is a single-component, non-curing insulating silicone thermal grease rated 1.0 ± 0.1 W/m·K (ASTM D5470) with dielectric strength of 2450 V/mm at 0.20 mm (IEC 60243), specific gravity 1.85 ± 0.08 g/cm³ and penetration 370 ± 20 (1/10 mm). It holds paste consistency from −50 °C to +200 °C, shows no powdering after 8 days of continuous 200 °C baking and no drying after 3 hours on a 280 °C heating platform, and is RoHS 2.0 compliant, non-toxic, odourless and non-corrosive.

This page is written for the people who have to approve a material rather than develop one: the EMS plant buyer, the brand owner outsourcing assembly, the sourcing manager adding a second source, and the quality team that has to close an audit finding. The technical data below is the same grade as our standard HN100; what this presentation adds is the documentation package, traceability, change control and landed cost model that a factory audit actually asks for.

1.0 W/mK Non-Curing Thermal Grease with 2450 V/mm Dielectric Strength for Heat Sink Assembly

The document package that ships with every lot

Audit findings on thermal interface materials are almost never about conductivity. They are about paper: a missing SDS, a certificate of analysis without a batch number, or a supplier that cannot say which drum went into which shipment. Below is what we issue, and what a buyer should request from any grease supplier.

Document What it answers in an audit When it is issued
Technical data sheet (TDS) Specification, test methods, operating limits, packaging and storage instructions With quotation and with every shipment
Safety data sheet (SDS) Hazard classification, handling, first aid, transport status With every shipment, and on request at quotation stage
Batch certificate of analysis (COA) Measured values for conductivity, gravity, penetration, oil separation, volatility, breakdown voltage against the TDS limits Per batch, on request or attached to the shipping documents
RoHS 2.0 declaration Restricted substance compliance for the finished paste With quotation, refreshed on request
Batch and lot traceability record Which production batch filled which drum, which drum went into which carton and shipment Maintained per lot, provided on request for audit or complaint investigation
Change notification (PCN) Notice before any formulation, raw material source, packaging or plant change that affects the approved part Issued before the change takes effect on your part number
Transport classification statement Confirms non-dangerous goods status so freight forwarders do not require DG handling With shipping documents
Buyer checklist: ask for the last three COAs of the same grade and compare the measured values, not just the pass or fail result. A supplier whose conductivity drifts batch to batch, even inside the tolerance, will drift your process window with it.
Dual sourcing without a second validation cycle

Most Southeast Asia assembly plants are now asked by their customers to name a second source for every critical material. With a non-curing paste, dual sourcing is simpler than with a two-component system, because there is no mix ratio, no pot life and no cure schedule to re-qualify.

Step What happens Audit evidence you keep
1. Sample 1 kg drum from the production batch, with COA of that batch Sample COA filed against the approved part number
2. Pilot run Same formulation run on your dispenser or screen printer, film thickness and coverage recorded Process parameter sheet and first article inspection report
3. Approval Drawing frozen with film thickness target, deposit pattern and torque spec Approved supplier list entry with the grade, pack size and TDS revision
4. Mass production Same formulation, same plant, same test methods, COA per batch Incoming inspection record comparing each lot to the approved sample

Because the grade does not cure, there is nothing in the material that changes state during storage or use, so the validation performed on the sample stays representative of production. That is the argument to put in front of your customer when they ask why the second source needs no new reliability programme: the material is thermodynamically the same paste at shipment and at assembly.

Incoming inspection: what to measure and how often
Check Method HN100 limit Frequency
Thermal conductivity ASTM D5470 1.0 ± 0.1 W/m·K Per batch COA, verify annually in house
Breakdown voltage IEC 60243 at 0.20 mm 2450 V/mm Per batch COA, verify on new supplier or new plant
Specific gravity GB/T 13354-1992 at 25 °C 1.85 ± 0.08 g/cm³ Every incoming lot, fast and cheap
Penetration GB/T 269-2023 at 25 °C 370 ± 20 (1/10 mm) Every incoming lot, catches consistency drift
Oil separation SH/T 0324-1992, 200 °C, 24 h ≤ 0.3 % Per batch COA, verify in house on new batches
Volatile matter SH/T 0337-92, 200 °C, 24 h ≤ 0.6 % Per batch COA, verify in house on new batches
Appearance and packaging Visual White or grey paste, sealed drum, label matches COA batch Every incoming lot

Specific gravity and penetration are the two checks we recommend on every incoming lot: they are quick, they need little equipment, and they catch the filling mistakes and raw material substitutions that a certificate alone will not reveal.

Landed cost model for a heat sink interface

Purchasing decisions on thermal interface materials are usually decided on price per kilogram, which is the wrong unit. The comparable unit is cost per assembled module, and it has six components.

Cost element What drives it How HN100 behaves
Material per module Contact area × film thickness × density 1.85 g/cm³ and thin film application keep grams per module low; a 25 cm² interface at 0.1 mm uses about 0.46 g
Packaging Container type and disposal 1 kg and 5 kg plastic drums, custom pack sizes; 5 kg drums reduce handling on high volume lines
Freight Weight, dangerous goods status Classified as non-dangerous goods, so no DG surcharge and no DG documentation on sea or air freight
Duty and origin HS code and certificate of origin Shipped from Shenzhen with the commercial invoice and origin documents the destination customs broker requests
Process cost Dispensing, cure, rework No curing step, no oven, no fixture; rework is wipe and re-apply instead of scrap
Scrap and yield Interface related failures Non-curing paste can be re-seated, so end of line failures are recoverable

Model it as material plus packaging plus freight plus process labour plus yield loss, divided by good modules shipped. On most lines the process and scrap terms dominate, and that is where a non-curing paste removes cost that a pad or a heat cure system adds back.

OEM packaging, labelling and shipment for importers
  • Standard packs are 1 kg and 5 kg plastic drums. Custom pack sizes are available on request, including sizes matched to a shift or a work order.
  • Private label and brand labelling can be agreed at order stage, with the label content and language supplied by the buyer or drafted by us for confirmation before production.
  • Each carton carries the grade, batch number, production date and net weight, so the receiving team can match the drum to the COA without opening it.
  • Shipments from Shenzhen to Vietnam, Thailand, Indonesia, Malaysia and the Philippines are routine; transport is non-dangerous goods with a 12 month shelf life below 27 °C, so sea freight consolidation does not shorten usable life.
Technical data (TDS HANAST-TDS-018 Rev.1)
Property Test method / condition Unit Value
Appearance Visual inspection – White or grey paste
Thermal conductivity ASTM D5470 W/m·K 1.0 ± 0.1
Specific gravity GB/T 13354-1992 / 25 °C g/cm³ 1.85 ± 0.08
Oil separation (oil bleed) SH/T 0324-1992 / 200 °C, 24 h % ≤ 0.3
Volatile matter SH/T 0337-92 / 200 °C, 24 h % ≤ 0.6
Penetration (cone penetration) GB/T 269-2023 / 25 °C 1/10 mm 370 ± 20
High temperature stability 200 °C constant temperature oven, 0.2 mm film – No powdering after 8 days continuous baking
Temperature resistance Heating platform 280 °C, 0.2 mm film – No drying after 3 hours continuous baking
Breakdown voltage IEC 60243 / 0.20 mm thickness V/mm 2450
Operating temperature range – °C −50 to +200
Compliance RoHS 2.0, non-toxic, odourless, non-corrosive – Compliant

Values are measured under standard conditions and are for reference only. Actual thermal performance depends on film thickness, surface flatness and contact pressure, so confirm the interface on your own hardware and keep the approved TDS revision in your supplier file.

Applications: 26 interface points across new energy vehicle, power supply and appliance assembly New energy vehicle and charging hardware
  • EV charger power module, AC wallbox and DC charger rectifier heat sink
  • Onboard charger (OBC), DC-DC converter and junction box power stage
  • Battery thermal management plate and BMS power board interface
  • Automotive electronics, car refrigerator and power module base plate
  • LED headlamp driver and vehicle lighting heat sink
Power supply and conversion
  • Switching mode power supply, AC-DC adapter and regulated power supply
  • Transformer, inductor and coil surface to housing
  • Rectifier bridge, thyristor and triac to grounded heat sink
  • LED driver, constant current driver and power supply module
  • Microwave device, microwave communication and transmission equipment
Heating, appliance and industrial
  • PTC heater, heating element and heat strip interface
  • Thermostat, thermal protector and temperature sensor point
  • Refrigerator, wine cooler and appliance compressor module
  • Inverter air conditioner outdoor board and IPM heat sink
  • UPS, server power supply and telecom rectifier module
  • VFD, servo drive and welding inverter power stage
Assembly and maintenance
  • Terminal, connector and busbar interface on insulated supports
  • Relay, contactor and fuse holder thermal path
  • Aluminium, copper, nickel plated and anodised surface combinations
  • Field service re-application and heat sink re-seating
  • CPU assembly, printer head and general heat sink mounting
  • HN100 insulating thermal grease documentation and batch packing for supplier audit
What each stakeholder should check before approving HN100

For the factory owner and plant manager

One grade covers the charger line, the power supply line and the service bench, so inventory is a single part number in 1 kg and 5 kg drums instead of several pad thicknesses. No cure step means no oven, no fixtures and no queue time before the next station, and a failed unit can be wiped and re-applied instead of scrapped.

For the purchasing and procurement team

MOQ is 1 kg, capacity is 50 tons per month and lead time is typically 7 to 15 days. Each shipment carries TDS, SDS and packing details, batch COAs are available on request, change notification is issued before any formulation or plant change, and non-dangerous goods classification keeps freight simple. Compare suppliers on cost per good module and on document completeness, not on price per kilogram alone.

For the process and manufacturing engineer

Apply by brush, roller, automatic dispensing or screen printing after solvent cleaning and drying. Freeze film thickness target, deposit pattern and torque spec in the assembly drawing, and record the dispenser parameters in the process sheet so a second line or a second shift reproduces the same interface. Penetration 370 ± 20 keeps the paste workable at thin film without stringing.

For the quality and reliability engineer

Use specific gravity and penetration on every incoming lot, and the full COA set on each batch. The two stability results that predict field behaviour are no powdering after 8 days at 200 °C and no drying after 3 hours at 280 °C on a 0.2 mm film; oil separation up to 0.3 percent and volatile matter up to 0.6 percent predict whether an interface dries out or fogs over time. Keep the approved sample sealed and labelled with its COA for comparison.

For the project and product manager

The HN family is a graded platform that can be positioned without changing supplier: 1.0 W/mK HN100 for insulating power supply interfaces, 2.05 W/mK HN200 for general electronics, 2.95 W/mK HN300 for clamped modules, 4.05 W/mK HN400 for charger and SiC interfaces, and metal-filled 5.0 to 6.0 W/mK grades for CPU and GPU duty. One supplier, one document set and one technical contact reduces the qualification workload when a product line expands.

Grade selection inside the HN thermal grease family
Grade Conductivity Dielectric strength Temperature range Best fit
HN100 1.0 W/m·K 2450 V/mm −50 to +200 °C Insulating power supply, transformer, PTC heater, thermostat
HN200 2.05 W/m·K 2450 V/mm −50 to +200 °C LED driver, adapter, general heat sink mounting
HN300 2.95 W/m·K 1850 V/mm −40 to +180 °C Clamped power module, cold plate interface
HN400 4.05 W/m·K 1100 V/mm −50 to +200 °C EV charger and SiC module, high heat flux
HN500 and HN600 5.0 to 6.0 W/m·K Metal-filled duty – CPU, GPU and server cooling
Application instructions
Step Action
1. Surface preparation Clean both surfaces with a solvent to remove grease, dust and oxidation, then dry completely.
2. Application Apply by brush, roller, automatic dispenser or screen printing, keeping the deposit inside the contact land area.
3. Spreading Spread evenly to the target film thickness. A thinner film transfers heat better than a thick one.
4. Thickness control Remove excess at the edges with a lint-free cloth to avoid paste entering creepage paths.
5. Assembly Assemble immediately and torque fasteners to specification to set a stable film thickness.
Packaging, storage and handling
  • Standard packs 1 kg and 5 kg plastic drums. Custom pack sizes available on request.
  • Store sealed below 27 °C, cool, dry and ventilated, away from direct sunlight. Shelf life 12 months when unopened.
  • Stir thoroughly before use if a small amount of silicone oil separates during storage. Performance is not affected.
  • Industrial use only. Wear nitrile gloves and safety goggles, ventilate the work area and avoid skin and eye contact. For eye contact rinse with clean water for 10 to 15 minutes and seek medical attention.
Q and A for sourcing, quality and engineering teams What documents do we receive with an HN100 order, and can they support a supplier audit?

Every shipment carries a technical data sheet, a safety data sheet and the packing information, and batch certificates of analysis are issued on request against the batch number printed on the drum. Batch and lot traceability records link the production batch to the drum and to the shipment, and change notification is issued before any formulation, raw material source, packaging or plant change that affects your approved part. That set is what an EMS audit typically asks for on a thermal interface material.

Can we add HN100 as a second source without running a new reliability programme?

In most cases yes, and the reason is that the material is non-curing: there is no mix ratio, no pot life and no cure schedule, so nothing in the paste changes state between shipment and assembly. The qualification that matters is the interface, so run a 1 kg sample from a production batch through your dispenser, compare film thickness and coverage against your current material, and file the sample COA with the first article report. Your reliability test on the assembly then covers both sources if the film thickness target is the same.

Which incoming checks catch a bad batch fastest?

Specific gravity and penetration. Both are quick, need little equipment and are sensitive to filling errors and raw material substitution, so they catch the majority of lot to lot problems before the material reaches the line. Add oil separation and volatile matter when a new batch is opened for a critical product, and compare every value against the approved sample rather than only against the pass or fail limit.

What are the MOQ, pack sizes, lead time and shipping terms to Southeast Asia?

MOQ is 1 kg. Standard packs are 1 kg and 5 kg plastic drums with custom sizes on request, and private label labelling can be agreed at order stage. Capacity is 50 tons per month and lead time is typically 7 to 15 days. The product is classified as non-dangerous goods, so sea and air freight to Vietnam, Thailand, Indonesia, Malaysia and the Philippines requires no dangerous goods handling, and shelf life of 12 months below 27 °C allows consolidated sea shipments.

How do we compare the true cost of a pad against HN100 per module?

Convert both to cost per good module. For the paste, multiply contact area by film thickness and density to get grams per module, then add packaging, freight, dispensing labour and scrap; for a 25 cm² interface at 0.1 mm that is about 0.46 g of paste at 1.85 g/cm³. For a pad, add the pad part number, die cutting, placement labour and the scrap caused by thickness tolerances. In most builds the labour and scrap terms decide the result, and a non-curing paste with rework capability removes cost that a pad or a heat cure system adds back.

About this supplier

Shenzhen Hanast New Materials Co., Ltd. is a China-based source factory for RTV-2 liquid silicone, potting compounds and thermal interface materials. Established in 2010 with a 40,000 m² production base, the company is an export-driven manufacturer with 70 to 80 percent of its business overseas, supplying B2B clients with OEM and ODM encapsulation and thermal management solutions.

Our range covers thermal grease from 1.0 to 6.0 W/m·K, thermally conductive potting compounds, silicone gels, mould making rubber and food grade silicone. Because the thermal grease and the potting compound for the same assembly come from one factory, your engineering team works with one technical contact and your purchasing team consolidates one supplier, one documentation set and one shipment schedule.

HN100 thermal grease 1 kg and 5 kg drum packaging for export

Send your approved part number, TDS revision and audit checklist and our team will return the matching grade, the document package for your supplier file and a 1 kg sample from a production batch for your pilot run.

Tell us the interface area, working voltage and annual volume, and we will reply with the cost per module estimate and a shipment schedule for Southeast Asia.