HN300 3.0 W/mK High Filler Loading Thermal Grease Paste – 0.82 °C·cm²/W Thermal Resistance Non-Curing Silicone Compound for IGBT Modules
HN300 is a single-component, non-curing high thermal conductivity silicone grease (also written as thermal paste, thermal compound, thermal conductive grease, heat transfer compound, heat sink compound, heat sink grease, thermal joint compound, thermal coupling grease or thermal interface material / TIM) built on a silicone oil (polydimethylsiloxane / PDMS) base with a high filler loading metal oxide system. Specific gravity reaches 2.5 ± 0.08 g/cm³, thermal conductivity is 2.95 ± 0.1 W/m·K and thermal resistance is 0.82 °C·cm²/W at 25 PSI, giving a low thermal resistance interface for IGBT modules, power modules and high power density assemblies. It almost never cures and keeps a grey, glossy, fine paste consistency from -40°C to +180°C, with near-zero free radical content and resistance to high and low temperatures, water, ozone and weathering. The material is safe, non-toxic, odorless (odourless), non-corrosive and compliant with RoHS 2.0.
Why Choose This Thermal Grease
- 2.95 ± 0.1 W/m·K high thermal conductivity (ASTM D5470) – roughly three times the heat transfer capability of standard 1.0 W/m·K grades, for IGBT modules and power components with high heat flux.
- 0.82 °C·cm²/W low thermal resistance at 25 PSI – thermal resistance and thermal impedance measured at a defined pressure, so interface performance can be compared directly with competing thermal compounds instead of relying on conductivity alone.
- High filler loading, 2.5 ± 0.08 g/cm³ specific gravity – a densely filled metal oxide system keeps the bond line thin and stable, which is what actually lowers case-to-heat-sink temperature in power stacks.
- Low oil bleed (≤ 0.3%) and low volatility (≤ 0.7%) at 200°C / 24 h – pump-out and dry-out risk stays controlled in vertically mounted, high vibration and long duty assemblies.
- 200°C 8-day no powdering, 280°C 5-6 hour no drying (0.2 mm film) – documented high temperature stability for thermal cycling, thermal shock and long-life power cycling qualification.
- Non-curing – almost never cures, will never dry or harden – paste consistency is maintained indefinitely, so heat sinks and modules can be re-seated, reworked and repaired without re-pasting the whole assembly.
- Near-zero free radical content – resists oxidation, embrittlement, UV and ozone attack, supporting a long service life under continuous thermal load.
- Electrical insulation with 1850 V/mm breakdown voltage at 0.20 mm (IEC 60243) – one material provides heat transfer and dielectric isolation for power modules and voltage regulators; for applications where the interface is fully enclosed, it also acts as a dielectric grease and water resistant barrier.
- Thixotropic, low consistency paste with 350 ± 20 penetration (1/10 mm) – holds its shape after stencil or screen printing, does not slump, and fills the microscopic gap between surfaces without running out of the joint.
- Water and humidity resistant – resistant to water, moisture, ozone and weathering, effectively waterproof inside sealed enclosures and suitable for damp heat environments.
- Wide workability – brushing, rolling, stencil printing, screen printing and automatic dispensing, compatible with manual benches and automated lines.
Technical Data
| Property |
Test Method / Condition |
Unit |
Value |
| Appearance |
Visual inspection |
— |
Grey, glossy, fine paste |
| Thermal Conductivity |
ASTM D5470 |
W/m·K |
2.95 ± 0.1 |
| Thermal Resistance |
ASTM D5470 @ 25 PSI |
°C·cm²/W |
0.82 |
| Specific Gravity |
GB/T 13354-1992 / 25°C |
g/cm³ |
2.5 ± 0.08 |
| Oil Separation (Oil Bleed) |
SH/T 0324-1992 / 200°C, 24 h |
% |
≤ 0.3 |
| Volatile Matter |
SH/T 0337-92 / 200°C, 24 h |
% |
≤ 0.7 |
| Penetration (Cone Penetration) |
GB/T 269-2023 / 25°C |
1/10 mm |
350 ± 20 |
| High-Temperature Stability |
200°C constant-temperature oven, 0.2 mm film |
— |
No powdering after 8 days continuous baking |
| Temperature Resistance |
Heating platform, 280°C, 0.2 mm film |
— |
No drying after 5-6 h continuous baking |
| Breakdown Voltage |
IEC 60243 / 0.20 mm thickness |
V/mm |
1850 |
| Operating Temperature Range |
— |
°C |
-40 to +180 |
| Curing Type |
— |
— |
Single-component, non-curing |
All values are measured under standard conditions and are for reference only. Actual thermal performance may vary with application conditions, bond line thickness (BLT) and contact pressure.
Applications
The paste is used as a thermal interface between heat-generating elements and heat dissipation facilities in electronic and electrical equipment:
- Power electronics: IGBT modules, power modules, power components, voltage regulators, rectifiers and regulated power supply units.
- Industrial drives and inverters: motor drives, servo amplifiers and welding equipment where a high filler loading grease keeps the bond line thin under pressure.
- Microwave and telecom: microwave devices, microwave communication and transmission equipment, microwave power supplies, telecom and 5G remote radio units.
- Automotive and EV: automotive electronics, car refrigerators, battery cooling plates and on-board charger (OBC) power stages.
- Thermal management components: transistors, CPU assemblies, thermistors, temperature sensors, printer heads, LED lighting interfaces.
- Servers and data centers: CPU and GPU cold plates, server power shelves and heat sinks in high power density racks.
- Repair and refurbishment: replacing dried-out factory compound in field service and EMS rework.
Application Instructions
- Surface preparation: clean all contact surfaces with a solvent to remove old grease, dust and oxidation; make sure the surfaces are completely dry.
- Application: apply the grease directly by brushing, rolling, automatic dispensing, stencil or screen printing.
- Spreading: transfer a small amount with a clean tool (razor blade, plastic spatula or clean knife) and spread evenly to the required thickness.
- Thickness control: the thinner the layer, the better the heat transfer; excess paste does not improve performance and may reduce efficiency, so wipe the edges with a lint-free cloth.
- Assembly: assemble the heat sink and heat source immediately and torque the fasteners to specification to keep a uniform bond line thickness (BLT) – 25 PSI is the reference pressure for the 0.82 °C·cm²/W value.
Packaging, Supply and Customization
- Standard packaging: 1 kg plastic drum and 5 kg plastic drum, supplied with MSDS and TDS; pail, bulk container and private label packaging available on request.
- Flexible filling: syringe, cartridge and tube filling for automated lines and retail-ready programs.
- MOQ: 1 kg, so trial orders and sample builds are supported before volume ramp-up.
- Lead time: 3-7 working days for stock, 15-25 days for production orders; supply ability 50 tons per month from our own factory, with fast delivery for repeat business.
- Payment terms: T/T, L/C and Western Union.
- OEM / ODM: six conductivity grades from 1.0 to 6.0 W/m·K are available, and viscosity, penetration, colour and filler loading can be tuned to your process; private label and custom packaging supported.
Compliance and Documents
- RoHS 2.0 and REACH compliant; non-toxic, odorless (odourless) and non-corrosive.
- TDS, MSDS and COA are supplied with the shipment (datasheet available on inquiry), and test reports for thermal conductivity, thermal resistance and dielectric strength can be issued on request.
- Classified as non-dangerous goods for transportation.
Storage and Shelf Life
- Store in the original, tightly sealed container in a cool, dry, well-ventilated area, protected from direct sunlight; recommended storage temperature below 27°C.
- Shelf life: 12 months from the date of manufacture when stored unopened and properly sealed, with good storage stability.
- A small amount of silicone oil may separate during storage; this is normal, does not affect performance and can be stirred before use.
FAQ
How is this grade different from a 1.0 W/m·K thermal grease? HN300 is a high filler loading compound: 2.95 ± 0.1 W/m·K with 0.82 °C·cm²/W at 25 PSI and 2.5 g/cm³ specific gravity, intended for IGBT and power modules where a standard thermal paste is not enough.
Will it dry out, pump out or harden? No. It is non-curing and almost never cures, and the interface will never dry out; oil separation is ≤ 0.3% and volatility ≤ 0.7% at 200°C / 24 h, so the interface stays workable and re-seatable.
Is thermal resistance data available at other pressures? The published 0.82 °C·cm²/W is measured at 25 PSI (ASTM D5470). Tell us your clamping pressure and we will advise the expected bond line thickness and interface performance.
Can it be dispensed on an automated line? Yes. Penetration is 350 ± 20 (1/10 mm) and the paste is thixotropic, so it dispenses, stencil prints and screen prints without slumping.
Do you support OEM, private label and custom grades? Yes. As a manufacturer we offer six grades from 1.0 to 6.0 W/m·K, custom viscosity and filler loading, private label packaging, bulk wholesale supply and free samples with TDS and MSDS.