HN300 High Thermal Conductive Silicone Grease is a single-component, non-curing, electrically insulating thermal compound engineered for long-term thermal management in electronics, LED lighting, power modules and automotive devices. It stays paste-like from −40 °C to +180 °C, never hardens in service, and complies with RoHS 2.0.
3.0 W/mKThermal conductivity
0.82°C·cm²/W thermal resistance
1850 V/mmDielectric breakdown
−40~+180 °COperating range
Product Description
HN300 is a single-component, non-curing, highly thermally conductive insulating silicone grease. It almost never cures and keeps its paste-like state for extended periods across a temperature range of −40 °C to +180 °C. The compound combines excellent electrical insulation with efficient heat transfer, and its near-zero free radical content gives it resistance to high and low temperatures, water, ozone and weathering.
With a thermal conductivity of 3.0 W/m·K and a thermal resistance of only 0.82 °C·cm²/W at 25 PSI, HN300 moves heat away from CPU assemblies, power modules and LED interfaces quickly and consistently. Its 1850 V/mm breakdown voltage keeps the bond line electrically safe in compact designs, while low oil separation (≤ 0.3%) and low volatile matter (≤ 0.7%) at 200 °C for 24 hours keep optical and electrical surfaces clean over long service life.
The grease is safe, non-toxic, odourless and non-corrosive, and fully complies with RoHS 2.0. It is supplied in 1 kg and 5 kg plastic drums, with custom sizes available on request.
Why Choose HN300
- Never cures, never dries out: the non-curing formula keeps its paste consistency indefinitely, so thermal contact does not degrade after repeated heat cycles.
- High conductivity at thin bond lines: 3.0 W/m·K at just 0.82 °C·cm²/W lets you use a minimal layer and still hit target case temperatures.
- Electrically safe: 1850 V/mm dielectric strength at 0.20 mm supports direct contact with live components in power supplies and inverters.
- Stable at extreme temperature: no powdering after 8 days at 200 °C and no drying after 5–6 hours on a 280 °C heating platform.
- Clean process: low oil bleed (≤ 0.3%) and low volatility (≤ 0.7%) protect sensitive optics, PCBs and inspection equipment.
- Easy to apply: suitable for brushing, rolling, screen printing, stencil printing and automatic dispensing lines.
Technical Parameters
| Property | Test Method / Condition | Unit | Value |
| Appearance | Visual inspection | — | Grey, glossy, fine paste |
| Thermal Conductivity | ASTM D5470 | W/m·K | 3.0 nominal (2.95 ± 0.1 per TDS) |
| Thermal Resistance | ASTM D5470 @ 25 PSI | °C·cm²/W | 0.82 |
| Specific Gravity | GB/T 13354-1992 / 25 °C | g/cm³ | 2.5 ± 0.08 |
| Oil Separation | SH/T 0324-1992 / 200 °C, 24 h | % | ≤ 0.3 |
| Volatile Matter | SH/T 0337-92 / 200 °C, 24 h | % | ≤ 0.7 |
| Penetration (Cone Penetration) | GB/T 269-2023 / 25 °C | 1/10 mm | 350 ± 20 |
| High-Temperature Stability | 200 °C oven, 0.2 mm film | — | No powdering after 8 days continuous baking |
| Temperature Resistance | Heating platform 280 °C, 0.2 mm film | — | No drying after 5–6 h continuous baking |
| Breakdown Voltage | IEC 60243 / 0.20 mm thickness | V/mm | 1850 |
| Operating Temperature Range | — | °C | −40 to +180 |
Typical Applications
- Thermal interface between heat-generating components and heat sinks in electronic and electrical equipment
- Surface coating or overall potting of microwave devices, microwave communication equipment, microwave power supplies and voltage regulators
- Thermal management for transistors, CPU assemblies, thermistors, temperature sensors, automotive electronics, car refrigerators, power modules and printer heads
- LED lighting heat dissipation interfaces, power supply modules and power components
- Inverter, charger and battery thermal pads where electrical insulation is required
Application Instructions
- Surface preparation: clean all contact surfaces with a solvent to remove grease, dust and oxidation; make sure surfaces are completely dry.
- Application: apply the grease by brushing, rolling, screen printing or automatic dispensing.
- Spreading: transfer a small amount with a clean razor blade, plastic spatula or clean knife and spread it evenly.
- Thickness control: the thinner the layer, the better the heat transfer; wipe excess from the edges with a lint-free cloth.
- Assembly: mount the heat sink or heat source immediately and torque fasteners to specification to control bond line thickness.
Packaging and Storage
- Standard packages: 1 kg plastic drum and 5 kg plastic drum; custom sizes available on request
- Store in original tightly sealed containers in a cool, dry, well-ventilated area away from direct sunlight, below 27 °C
- Shelf life: 12 months from date of manufacture when stored unopened and properly sealed
- Stir thoroughly before use if a small amount of silicone oil separates during storage; thermal performance is not affected
Frequently Asked Questions
What is the thermal conductivity of HN300?3.0 W/m·K typical, with 0.82 °C·cm²/W thermal resistance at 25 PSI, tested by ASTM D5470.
Does HN300 cure or harden?No. It is a single-component non-curing grease that keeps its paste consistency in service and does not dry out.
What is the operating temperature range?−40 °C to +180 °C, with no powdering after 8 days at 200 °C and no drying after 5–6 hours at 280 °C.
Is it electrically insulating?Yes. Breakdown voltage is 1850 V/mm at 0.20 mm thickness according to IEC 60243.
Will oil separate during storage?A small amount of silicone oil may separate, which is normal. Oil separation is ≤ 0.3% at 200 °C for 24 h, and stirring before use restores the paste.
How thick should the layer be?Use the thinnest layer that guarantees full surface contact. Excess grease does not improve heat transfer and can reduce efficiency.
What is the minimum order quantity and lead time?MOQ is 1 kg with negotiable pricing; standard orders ship in 5–7 days, with 20 tons per month supply capacity.
Is HN300 RoHS compliant?Yes, it complies with RoHS 2.0 and is non-toxic, odourless and non-corrosive.
Need a thermal grease sample or bulk quotation?
Send your application details, target thermal conductivity and packaging requirement. Our engineers reply with a matched grade, TDS and MSDS within one working day.