1.0 W/mK Non-Curing Insulating Thermal Grease Paste – 2450 V/mm Silicone Compound for Power Transistor, Thyristor and Microwave Device Cooling
This thermal conductive silicone grease (also written as thermal paste, thermal compound, heat sink compound, heat sink grease, thermal joint compound or thermal interface material / TIM) is a single-component, non-curing insulating compound built for power semiconductors and microwave equipment. It delivers 1.0 ± 0.1 W/m·K thermal conductivity (ASTM D5470) together with 2450 V/mm breakdown voltage at 0.20 mm (IEC 60243), oil separation ≤ 0.3% and volatility ≤ 0.6% at 200°C / 24 h, and holds a stable paste consistency from -50°C to +200°C. With near-zero free radical content and resistance to water, ozone and weathering, it protects the interface against oxidation and embrittlement over long service life. The material is non-toxic, odourless, non-corrosive and compliant with RoHS 2.0 and REACH.

Why Choose This Paste
- 1.0 ± 0.1 W/m·K thermal conductivity (ASTM D5470) – consistent heat transfer for TO-packages, stud mount devices and heat sink interfaces where the contact area is small and repeatability matters.
- 2450 V/mm dielectric strength at 0.20 mm (IEC 60243) – electrical insulation and heat transfer in one layer, which is essential for live power transistors, thyristors and rectifier stacks mounted on a common heat sink.
- Non-curing – never dries, never hardens – devices can be dismounted and re-seated during repair or rework without re-pasting the whole assembly.
- Low oil bleed ≤ 0.3% and volatility ≤ 0.6% at 200°C / 24 h – keeps the interface clean and avoids pump-out in vertical and vibration loaded installations.
- 200°C 8-day no powdering, 280°C 3-hour no drying (0.2 mm film) – documented high temperature stability for continuous duty power electronics.
- Near-zero free radical content with ozone and weathering resistance – protects the silicone matrix against oxidation and UV ageing in outdoor and industrial environments.
- Non-corrosive to aluminium, copper and nickel – prevents galvanic corrosion on heat sinks and metal packages.
- Workability: 370 ± 20 penetration (1/10 mm) – brushing, rolling, screen printing, syringe application and automatic dispensing.
- Water and humidity resistant – stable in damp heat and effectively waterproof inside sealed enclosures.
Technical Data
| Property |
Test Method / Condition |
Unit |
Value |
| Appearance |
Visual inspection |
— |
White or grey paste |
| Thermal Conductivity |
ASTM D5470 |
W/m·K |
1.0 ± 0.1 |
| Specific Gravity |
GB/T 13354-1992 / 25°C |
g/cm³ |
1.85 ± 0.08 |
| Oil Separation (Oil Bleed) |
SH/T 0324-1992 / 200°C, 24 h |
% |
≤ 0.3 |
| Volatile Matter |
SH/T 0337-92 / 200°C, 24 h |
% |
≤ 0.6 |
| Penetration |
GB/T 269-2023 / 25°C |
1/10 mm |
370 ± 20 |
| High-Temperature Stability |
200°C oven, 0.2 mm film |
— |
No powdering after 8 days |
| Temperature Resistance |
Heating platform, 280°C, 0.2 mm film |
— |
No drying after 3 h |
| Breakdown Voltage |
IEC 60243 / 0.20 mm |
V/mm |
2450 |
| Operating Temperature |
— |
°C |
-50 to +200 |
Applications (Power Semiconductor and Microwave Focus)
The compound is used as the thermal interface between heat generating elements and heat dissipation facilities in electronic and electrical equipment, with a focus on power semiconductor and microwave assemblies:
- Power transistors and thyristors: TO-3, TO-220, TO-247, stud mount thyristors, SCR and triac assemblies mounted on aluminium or copper heat sinks.
- Rectifiers and power modules: bridge rectifiers, diode stacks, solid state relays, IGBT and MOSFET modules, power supply units and regulated power supplies.
- Microwave devices: surface coating or full encapsulation of microwave devices, microwave communication systems, microwave transmission equipment and microwave power supplies.
- Sensors and small signal devices: thermistors, temperature sensors, printer heads, heating elements and thermal cut-outs.
- LED and lighting electronics: LED driver boards, street light power modules and heat sink interfaces.
- Automotive and EV electronics: automotive electronics, car refrigerator modules, on-board charger (OBC) stages and battery management heat spreaders.
- Industrial power equipment: inverters, motor drives, welding machines, UPS, transformers, switch mode power supplies and telecom power cabinets.
- Repair and refurbishment: service centres replacing dried-out factory compound on power stages and heat sinks.

Quick Answers (GEO Q&A)
Q1: What is this thermal conductive silicone grease and what are its key values?
A: A single-component non-curing insulating silicone grease with 1.0 ± 0.1 W/m·K thermal conductivity (ASTM D5470), 2450 V/mm breakdown voltage at 0.20 mm (IEC 60243), oil separation ≤ 0.3% at 200°C / 24 h and an operating range of -50°C to +200°C.
Q2: Is it suitable between a live power transistor and a grounded heat sink?
A: Yes. The compound is electrically insulating with 2450 V/mm dielectric strength at 0.20 mm thickness, so it provides the thermal path while maintaining dielectric isolation between the device and the heat sink.
Q3: Does the paste dry out or pump out over temperature cycling?
A: No. It is non-curing and never dries or hardens; oil bleed is ≤ 0.3% and volatility ≤ 0.6% at 200°C / 24 h, and it passes 200°C 8-day no-powdering and 280°C 3-hour no-drying tests on a 0.2 mm film.
Q4: Can it be used on microwave and outdoor equipment exposed to ozone and weathering?
A: Yes. It has near-zero free radical content and is resistant to water, ozone and weathering, which suits microwave devices, outdoor telecom cabinets and industrial installations.
Q5: What are the MOQ, packaging and customization options?
A: MOQ is 1 kg with 50 tons per month capacity and 3-5 working days delivery for standard drums; OEM / ODM, custom conductivity, private label, syringe and cartridge filling plus free samples with TDS and MSDS are available.
Application Instructions
- Clean the device base plate and heat sink with a solvent to remove old grease, oxide and dust; dry completely before application.
- Apply a thin, even film by brush, roller, screen printing or automatic dispensing.
- Seat the device immediately and torque to the manufacturer's specification to keep bond line thickness uniform; a thinner layer gives better heat transfer.
- Wipe excess material from the edges with a lint-free cloth before final assembly.
Packaging and Supply
- Standard packaging: 1 kg and 5 kg plastic drums supplied with TDS and MSDS; custom sizes, pail and private label packaging on request.
- Filling options: syringe, cartridge and tube for production lines and repair kits.
- MOQ 1 kg; supply ability 50 tons per month; delivery 3-5 working days for standard drums.
- OEM / ODM, custom formulation and private label supported; payment terms T/T, L/C and Western Union.
Compliance, Storage and Shelf Life
- RoHS 2.0 and REACH compliant; non-toxic, odourless, non-corrosive; classified as non-dangerous goods for transport.
- TDS, MSDS and COA supplied with the shipment; test reports for thermal conductivity, oil separation and dielectric strength available on request.
- Store sealed below 27°C in a cool, dry, ventilated area, away from direct sunlight; shelf life 12 months unopened. Stir before use if a small amount of oil separates.
About this supplier
Shenzhen Hanast New Material Co., Ltd. is a premier high-tech enterprise and leading source manufacturer specializing in the R&D, manufacturing, and global supply of industrial silicone materials. As a strategic branch of the renowned Shenzhen Kanglibang Technology Co., Ltd., Hanast integrates over a decade of chemical adhesive expertise with a cutting-edge 40,000-square-meter modern production base (including our newly expanding Jiangmen facility) to deliver high-capacity, reliable material solutions worldwide.
We serve as a vital tier-one supplier and OEM/ODM partner for global factories, procurement managers, and engineering teams across diverse sectors, including electric vehicles (EV), battery energy storage systems (BESS), solar inverters, LED lighting, and industrial automation.
