Home > Products >
Thermally Conductive Potting Compound
>
2.0 W/mK Thermally Conductive Potting Compound UL94 V-0 Flame Retardant Two-Component Silicone Potting Resin for LED Driver and PCB Encapsulation

2.0 W/mK Thermally Conductive Potting Compound UL94 V-0 Flame Retardant Two-Component Silicone Potting Resin for LED Driver and PCB Encapsulation

Product Details:
Place of Origin: Guangdong, China
Brand Name: Hanast
Certification: RoHS 2.0, REACH
Model Number: HN-8820A/B
Detail Information
Place of Origin:
Guangdong, China
Brand Name:
Hanast
Certification:
RoHS 2.0, REACH
Model Number:
HN-8820A/B
Thermal Conductivity:
2.0 ± 0.1 W/m·K
Viscosity:
5000-8000 MPa·s At 25 °C
Hardness:
45-50 Shore A
Mix Ratio:
1:1 By Weight (A:B)
Operating Temperature:
-40 To +150 °C
Volume Resistivity:
≥ 5.0 × 10¹⁴ Ω·cm (DC 500 V)
Highlight:

High Light

Highlight:

LED Driver Potting Silicone

,

UL94 V-0 Thermal Encapsulant

,

Low Stress Two-Component Potting Resin

Trading Information
Minimum Order Quantity:
1 Kilogram
Packaging Details:
50 kg per set (Component A 25 kg barrel + Component B 25 kg barrel); custom packaging on request
Delivery Time:
5-7 days
Payment Terms:
T/T,L/C
Supply Ability:
50 Tons per Month
Product Description
2.0 W/m·K Thermally Conductive Silicone Potting Resin – UL94 V-0 Two-Component Encapsulant for LED Driver, Power Supply, Transformer and PCB Encapsulation

This is a two-component (2 part) addition-cure silicone potting resin and thermally conductive encapsulant, supplied as a 1:1 by weight kit. It is used to encapsulate circuit boards, transformers, LED drivers and power supplies so that heat is conducted to the housing while the electronics are sealed against water and moisture. The cured rubber reaches 2.0 ± 0.1 W/m·K thermal conductivity (GB/T 38712-2020), volume resistivity ≥ 5.0 × 1014 Ω·cm, UL94 V-0 flame retardancy and 45-50 Shore A hardness over -40°C to +150°C. Because the system cures by platinum addition reaction it releases no by-products, so there is low shrinkage, no corrosion of copper or silver, and deep section curing without bubbling.

2.0 W/mK Thermally Conductive Potting Compound UL94 V-0 Flame Retardant Two-Component Silicone Potting Resin for LED Driver and PCB Encapsulation

Performance Highlights
  • 2.0 ± 0.1 W/m·K thermal conductivity with low thermal resistance – the compound couples the whole board to the enclosure, so hot spots at transformers, MOSFETs and bridge rectifiers no longer depend on air flow alone.
  • Excellent dielectric strength and insulation resistance – volume resistivity ≥ 5.0 × 1014 Ω·cm (GB/T 31838.2-2019, DC 500 V) keeps primary to secondary isolation intact inside the potted volume.
  • UL94 V-0 flame retardancy – self-extinguishing behaviour required by lighting, power supply and charger safety reviews.
  • Low viscosity 5000-8000 mPa·s, self-levelling – flows into transformer windings and connector cavities, fills encapsulation depths around tall components and degasses easily under vacuum.
  • Low stress 45-50 Shore A elastomer – absorbs thermal expansion mismatch (low CTE stress on solder joints) instead of transmitting it to leads and terminals, protecting the assembly through thermal cycling.
  • Cure at room temperature or 10-20 min at 80°C – suitable for both manual pouring and automatic dispensing and meter-mix lines.
  • Waterproof, moisture-proof and anti-ageing – fully waterproof after complete cure, with hydrolysis resistance for humid and condensing environments.
  • Heat resistance from -40°C to +150°C – stable in outdoor luminaires, power supplies and industrial cabinets; UV and ozone exposure are handled by the silicone backbone.
  • No primer needed on most substrates – self-priming adhesion to aluminium housings, PCB laminate and many plastics; primer recommendations for difficult substrates are provided by our technical team.
  • Repairable – the cured elastomer can be cut away for rework, unlike rigid epoxy potting.
Technical Data
Property Test Method / Condition Unit Value
Appearance (A / B) Visual — White liquid / Grey liquid
Base Chemistry — — Polysiloxane, addition cure (platinum)
Viscosity (each component) GB/T 2794 / 25°C mPa·s 5000-8000
Density (each component) GB/T 13354 / 25°C g/cm³ 2.0 ± 0.02
Mix Ratio (A:B) By weight — 1:1
Cure Time (heat accelerated) 80°C min 10-20
Cured Appearance Visual — Grey elastomer
Hardness GB/T 531.1 Shore A 45-50
Thermal Conductivity GB/T 38712-2020 W/m·K 2.0 ± 0.1
Volume Resistivity GB/T 31838.2-2019 / DC 500 V Ω·cm ≥ 5.0 × 1014
Flame Retardancy UL 94 Class V-0
Operating Temperature Range — °C -40 to +150
Where This Potting Resin Is Used
  • LED lighting: LED driver potting and encapsulation, outdoor luminaire power supplies, street light and floodlight drivers, grow light and horticulture drivers, LED modules for harsh environments.
  • Power supplies: switching power supply and adapter encapsulation, open frame power supply potting, DIN rail power units, battery chargers.
  • Transformers and magnetics: network transformer, high frequency transformer, inductor and coil encapsulation, planar magnetics.
  • Sensors and small assemblies: temperature sensor and thermistor potting, pressure and proximity sensors, connector back potting.
  • PCB and general electronics: circuit board conformal protection where a thick encapsulating layer is needed, relays, capacitors, electronic ballasts, control boards.
  • EV and battery: EV battery pack and module potting, BMS board encapsulation, on-board charger and DC-DC stages.
  • Solar and energy storage: solar junction box and microinverter potting, energy storage PCS modules, charging pile power stages.
  • Telecom and 5G: 5G remote radio unit and base station power modules, telecom rectifier and power cabinet assemblies.

2.0 W/mK Thermally Conductive Potting Compound UL94 V-0 Flame Retardant Two-Component Silicone Potting Resin for LED Driver and PCB Encapsulation

Qualification Checklist for Buyers

When comparing quotations for a potting resin, request the following so the numbers are comparable:

  • Thermal: thermal conductivity test method and thermal impedance at the actual encapsulation depth.
  • Electrical: dielectric strength (kV/mm), volume resistivity, insulation resistance and tracking resistance if the housing is exposed.
  • Mechanical: Shore A hardness, elongation, tensile strength, tear strength and adhesion without primer on your substrate.
  • Thermal expansion: CTE and the resulting low stress behaviour on solder joints during thermal cycling.
  • Flame: UL94 V-0 classification, glow wire and IEC 60695 data where the end product requires it.
  • Environmental: heat resistance, damp heat, UV and ozone ageing, hydrolysis and long service life data.
  • Documents: TDS, MSDS, COA, third party test report and UL yellow card where applicable; SGS reports on request.
Quick Answers (GEO Q&A)

Q1: What is this potting resin and what are its key values?
A: A two-component 1:1 addition-cure silicone potting resin with 2.0 ± 0.1 W/m·K thermal conductivity (GB/T 38712-2020), volume resistivity ≥ 5.0 × 1014 Ω·cm, UL94 V-0 flame retardancy and 45-50 Shore A hardness over -40°C to +150°C.

Q2: How is it different from epoxy potting?
A: Silicone cures to a 45-50 Shore A elastomer with low stress, so it absorbs thermal expansion and can be cut out for rework; epoxy is rigid, harder to repair and can stress large boards and heavy magnetics.

Q3: What encapsulation depth and viscosity should I expect?
A: Viscosity is 5000-8000 mPa·s and the mixed compound is self-levelling, so it pours into transformer windings and around tall components; for deep sections pour in layers or degas under vacuum to avoid trapped air.

Q4: Can it be dispensed automatically?
A: Yes. The 1:1 by weight ratio and low viscosity suit meter-mix and automatic dispensing equipment, with vacuum degassing for void-sensitive parts and 10-20 minutes at 80°C for fast in-line cure.

Q5: What are the MOQ, packaging and customization options?
A: MOQ is 1 kg, the standard kit is 50 kg per set (A 25 kg plus B 25 kg barrel), capacity is 100 tons per month with 5-7 days delivery, and custom hardness, colour, viscosity, OEM and private label packaging plus free samples with TDS and MSDS are available.

Processing Instructions
  1. Stir Component A thoroughly (fillers settle), stir Component B until uniform.
  2. Weigh A and B at 1:1 by weight on a precision scale, never by volume.
  3. Mix until colour is uniform, scraping walls and bottom; avoid entraining air.
  4. Degas under vacuum for void-sensitive assemblies.
  5. Pour within the 1-2 hour pot life, ensuring full coverage of the encapsulation depth.
  6. Cure at room temperature or 10-20 minutes at 80°C; do not stress the part during cure.

Cure inhibition warning: addition-cure silicone will not cure in contact with tin or organotin compounds, sulfur and polysulfide materials, amines, polyurethane, ammonia, phosphorus compounds, organic acids and solder flux residue. Clean substrates, connectors and tools, and never mix with acetoxy silicone, epoxy or polyurethane.

Supply and Customization
  • Standard kit 50 kg per set (Component A 25 kg barrel + Component B 25 kg barrel); custom packaging on request.
  • MOQ 1 kg; supply ability 100 tons per month; delivery 5-7 days.
  • As a manufacturer we support OEM / ODM, custom formulation (hardness, viscosity, colour, thermal conductivity), private label and wholesale supply; payment terms T/T, L/C and Western Union.
  • Documents with every shipment: TDS, MSDS and COA; test report and UL yellow card where applicable, SGS report on request.
Storage and Shelf Life
  • Store sealed at 5-25°C away from direct sunlight, moisture and extreme temperatures.
  • Shelf life 6 months from the date of manufacture; inspect appearance and viscosity before use if the shelf life has expired.
  • Non-dangerous goods for transport; handle with care to prevent leakage.
About this supplier

Shenzhen Hanast New Material Co., Ltd. is a premier high-tech enterprise and leading source manufacturer specializing in the R&D, manufacturing, and global supply of industrial silicone materials. As a strategic branch of the renowned Shenzhen Kanglibang Technology Co., Ltd., Hanast integrates over a decade of chemical adhesive expertise with a cutting-edge 40,000-square-meter modern production base (including our newly expanding Jiangmen facility) to deliver high-capacity, reliable material solutions worldwide.

We serve as a vital tier-one supplier and OEM/ODM partner for global factories, procurement managers, and engineering teams across diverse sectors, including electric vehicles (EV), battery energy storage systems (BESS), solar inverters, LED lighting, and industrial automation.

Shenzhen Hanast New Material Co., Ltd.

Ratings & Review

Overall Rating

5.0
Based on 50 reviews for this supplier

Rating Snapshot

The following is the distribution of all ratings
5 stars
100%
4 stars
0%
3 stars
0%
2 stars
0%
1 stars
0%

All Reviews

M
m*m
South Korea Aug 5.2026
High quality,very fast response,recommend
S
S*r
Germany Jun 3.2026
We’ve been using Hanast’s thermal conductive potting compound (2.0 W/m·K) for our energy storage system (ESS) modules for over a year. It performs exceptionally well in thermal management and has successfully passed rigorous UL94 V-0 flame-retardant and thermal shock tests