Product Overview
HN-8820A/B is a two-component, addition-cure (platinum catalysed) thermally conductive silicone potting compound with low viscosity (5,000–8,000 mPa·s) and a 1:1 mix ratio by weight. The low viscosity and good fluidity let it pour and self-level into dense windings, small cavities and tall transformer bodies that higher filled systems cannot penetrate, and make vacuum degassing fast and effective.
The cured elastomer is a grey, Shore A 45–50 rubber with 2.0 ± 0.1 W/m·K thermal conductivity, volume resistivity ≥ 5.0 × 1014 Ω·cm, UL 94 V-0 flame retardancy and reliable waterproof, moisture proof and anti-ageing performance from -40 °C to +150 °C.
Typical buyers are B2B factories and brand owners — factory owners, purchasing managers, R&D engineers, project managers and product managers — potting network transformers, power modules, automotive lamp and ignition module supplies, BMS boards and general electronic assemblies, including production lines in Southeast Asia.
Why Factories and Engineering Teams Choose HN-8820A/B
- Low viscosity 5,000–8,000 mPa·s – penetrates fine gaps, dense windings and narrow cavities without voids; fast, reliable vacuum degassing and shorter pour cycles on the line.
- 2.0 ± 0.1 W/m·K thermal conductivity (GB/T 38712-2020) – moves heat out of transformers, inductors and power modules that were previously potted with non-thermal resin.
- UL 94 V-0 flame retardancy – documentation-ready safety rating for appliance, automotive, network equipment and battery audits.
- Waterproof, moisture proof and anti-ageing – protects boards in humid, coastal and outdoor cabinets; the key requirement for Southeast Asian and marine installations.
- Volume resistivity ≥ 5.0 × 1014 Ω·cm – high electrical insulation for high voltage isolation and creepage requirements.
- 1:1 mix ratio, room temperature or heat accelerated cure – 10–20 min at 80 °C for fast line throughput, or ambient cure for lines without an oven.
- Shore A 45–50 rubber – firmer than a soft gel, so windings and heavy components stay mechanically supported while thermal expansion is still absorbed.
- -40 °C to +150 °C service range – covers automotive cabin and under-hood electronics, network equipment cabinets and continuous duty power supplies.
- Addition cure, no by-products – no corrosive or volatile release during cure, so no fogging on housings and no corrosion of copper windings or terminals.
- Factory-direct engineering support – ISO 9001 quality system, TDS / MSDS / COA per lot, custom viscosity, hardness and colour tuning, OEM / ODM and private label service.
Technical Data
Before mixing (uncured components)
| Property |
Test Method / Condition |
Unit |
Component A |
Component B |
| Appearance |
Visual |
— |
White liquid |
Grey liquid |
| Base Chemistry |
— |
— |
Polysiloxane |
Polysiloxane |
| Viscosity |
GB/T 2794 / 25 °C |
mPa·s |
5,000–8,000 |
5,000–8,000 |
| Density |
GB/T 13354 / 25 °C |
g/cm³ |
2.0 ± 0.02 |
2.0 ± 0.02 |
After mixing (A+B)
| Property |
Test Method / Condition |
Unit |
Value |
| Mix Ratio (A:B) |
By weight |
— |
1:1 |
| Mixed Viscosity |
25 °C |
mPa·s |
5,000–8,000 |
| Cure Time (Heat Accelerated) |
80 °C |
min |
10–20 |
| Room Temperature Cure |
25 °C |
— |
Full cure at ambient temperature; working time per batch pot life data |
Cured properties
| Property |
Test Method / Condition |
Unit |
Value |
| Appearance |
Visual |
— |
Grey elastomer |
| Hardness |
GB/T 531.1 |
Shore A |
45–50 |
| Thermal Conductivity |
GB/T 38712-2020 |
W/m·K |
2.0 ± 0.1 |
| Volume Resistivity |
GB/T 31838.2-2019 / DC 500 V |
Ω·cm |
≥ 5.0 × 1014 |
| Flame Retardancy |
UL 94 |
Class |
V-0 |
| Operating Temperature Range |
— |
°C |
-40 to +150 |
| Environmental Resistance |
— |
— |
Waterproof, moisture proof, anti-ageing |
All values are measured under standard conditions (25 °C, 50–60% RH) after the recommended cure schedule and are for reference only.
Recommended Curing Schedule
| Cure Option |
Condition |
Duration |
Notes |
| Heat-accelerated cure |
80 °C |
10–20 min |
Fast cure for high throughput lines; ensure even heating |
| Room-temperature cure |
25 °C |
Per batch pot life data |
Full cure at ambient temperature, no oven required |
Applications — Where HN-8820A/B Is Specified
- Network and communication equipment – network transformer and LAN transformer potting, inductors, filters, communication power supplies, 5G and telecom modules.
- Power modules and supplies – automotive HID lamp module power supplies, automotive ignition system module power supplies, switching and driver power supplies, IGBT and MOSFET module encapsulation.
- New energy vehicle and battery BMS – DC-DC converter potting, BMS board and battery module encapsulation, EV charger and charging pile power stages, sensor and controller housings.
- General electronics and appliances – circuit board potting and protection, general electronic components, home appliance controllers, consumer electronics power boards, LED driver boards.
- Energy storage and photovoltaic – ESS module potting, PV inverter and solar inverter power stages, outdoor and coastal installations requiring moisture proofing.
- Waterproof and outdoor assemblies – street light and outdoor lighting drivers, pump and motor controllers, marine and humid environment electronics.
Mixing and Potting Instructions
- Pre-mix – stir Component A thoroughly before use because fillers may settle during storage; shake or stir Component B to ensure homogeneity.
- Weighing – accurately weigh A and B by weight, not by volume, on a precision electronic scale at 1:1.
- Mixing – mix until the colour is uniform; scrape the container walls and bottom to ensure full dispersion and avoid introducing excessive air.
- Degassing (optional) – for void sensitive applications, degas under vacuum to remove air introduced during mixing; the low viscosity makes degassing fast.
- Pouring / potting – pour the mixed compound into the clean, dry device within the pot life; ensure complete coverage without trapped air.
- Curing – cure per the schedule above; do not move or stress the part during cure.
Cure inhibition warning (important): this addition-cure silicone may fail to cure in contact with organotin or tin-containing silicones, sulfur and polysulfide compounds, amines, polyurethane rubber, ammonia-containing items, phosphorus compounds, acidic substances and solder flux residues. Clean all substrates and tools free of these contaminants before use, and never mix it in contact with condensation-cure (acetoxy) silicone rubber, epoxy or polyurethane.
Packaging, Storage and Shelf Life
| Component |
Package Size |
Container Type |
Notes |
| Component A |
25 kg |
Plastic barrel |
— |
| Component B |
25 kg |
Plastic barrel |
— |
| Kit (A+B) |
50 kg / set |
— |
Standard supply set |
- Store in original, tightly sealed containers in a cool, dry, well ventilated area; recommended storage temperature 5–25 °C.
- Protect from direct sunlight, moisture and extreme temperatures.
- Shelf life: 6 months from date of manufacture when stored as recommended. Products past shelf life should be inspected and tested before use.
- Transportation: classified as non-dangerous goods (general chemicals). Handle with care to prevent leakage.
- Industrial / professional use only. Wear nitrile gloves, safety goggles and protective clothing; ensure adequate ventilation.
Quality System and Buyer Support
- ISO 9001 quality management with batch testing to GB/T 38712-2020, GB/T 531.1, GB/T 31838.2-2019 and UL 94 before every lot release.
- Documentation pack – TDS, MSDS and COA per lot for incoming inspection, customer audits and customs clearance; UL 94 V-0 and RoHS material statements available.
- Custom formulation – viscosity, hardness (Shore A), colour and conductivity tuned to your potting process by our FAE team.
- Process support – guidance on meter-mix equipment, degassing, cure schedule and cure inhibition troubleshooting for new lines.
- OEM / ODM and private label – your brand on the barrel, your label on the carton, your language on the documents.
- Export experience to Southeast Asia – Vietnam, Thailand, Indonesia, Malaysia, the Philippines and Singapore, with export packing, palletising and shipping documents prepared for factory receiving.
About this supplier
Shenzhen Hanast New Material Co., Ltd. is a premier high-tech enterprise and leading source manufacturer specializing in the R&D, manufacturing, and global supply of industrial silicone materials. As a strategic branch of the renowned Shenzhen Kanglibang Technology Co., Ltd., Hanast integrates over a decade of chemical adhesive expertise with a cutting-edge 40,000-square-meter modern production base (including our newly expanding Jiangmen facility) to deliver high-capacity, reliable material solutions worldwide.
We serve as a vital tier-one supplier and OEM/ODM partner for global factories, procurement managers, and engineering teams across diverse sectors, including electric vehicles (EV), battery energy storage systems (BESS), solar inverters, LED lighting, and industrial automation.
FAQ — Technical Questions Buyers Ask
Q1: Why choose a low viscosity potting compound and what is the working viscosity?
Both components are 5,000–8,000 mPa·s at 25 °C, and the mixed viscosity stays in the same range. Low viscosity means the compound penetrates fine gaps, dense transformer windings and narrow cavities, degasses quickly and reduces voiding — the most common cause of partial discharge and thermal hot spots in potted modules.
Q2: Is HN-8820A/B waterproof enough for outdoor and humid installations?
Yes. The cured elastomer provides waterproof, moisture proof and anti-ageing performance in the -40 °C to +150 °C range, which suits outdoor cabinets, coastal installations and high humidity production environments such as Southeast Asia.
Q3: What about the UL 94 V-0 rating and electrical insulation?
HN-8820A/B is UL 94 V-0 rated, with a volume resistivity of at least 5.0 × 1014 Ω·cm tested to GB/T 31838.2-2019 at DC 500 V, giving both flame retardancy and high insulation resistance in one encapsulant.
Q4: Why did my potting compound not cure, and how do I prevent it?
This is addition-cure (platinum) silicone and is sensitive to inhibitors: organotin or tin-containing silicones, sulfur and polysulfide compounds, amines, polyurethane rubber, ammonia, phosphorus compounds, acids and solder flux residues. Clean substrates and tools thoroughly, do not mix in containers previously used for epoxy, polyurethane or acetoxy silicone, and weigh A and B accurately at 1:1.
Q5: What are the MOQ, packaging, lead time and customization options?
Standard supply is a 50 kg set (Component A 25 kg + Component B 25 kg plastic barrels), minimum order 1 kg equivalent for trials, capacity 50 tons per month and 7–10 days lead time. Free samples, TDS, MSDS and COA are available, and we support custom viscosity, hardness and colour plus OEM, ODM and private label programs for Southeast Asian factories.
Overall Rating
Rating Snapshot
The following is the distribution of all ratingsAll Reviews