Product Overview
HN-8830A/B is a two-component, addition-cure (platinum catalysed) thermally conductive silicone potting compound developed for high power electronic assemblies that need both heat dissipation and long term temperature resistance. It mixes 1:1 by weight, flows and self-levels into dense assemblies, and cures either at room temperature or with heat acceleration.
The cured elastomer stays rubber-elastic from -40 °C to +200 °C and delivers 3.0 ± 0.1 W/m·K thermal conductivity with excellent electrical insulation and UL 94 V-0 flame retardancy. Shore A 35 ± 8 low modulus means the cured gel absorbs thermal expansion and vibration instead of transferring stress to solder joints, ceramic capacitors, IGBT terminals and thin bond wires — the usual failure point of rigid epoxy encapsulation.
Typical buyers are B2B factories and brand owners — factory owners, purchasing managers, R&D engineers, project managers and product managers — in new energy vehicle and battery BMS, power modules, switching power supplies, home appliance controllers and automotive electronics, including production lines in Southeast Asia.

Why Factories and Engineering Teams Choose HN-8830A/B
- 3.0 ± 0.1 W/m·K thermal conductivity (GB/T 38712-2020) – real potting level heat transfer for power modules, DC-DC converters and BMS boards, not just a surface interface film.
- UL 94 V-0 flame retardancy – a documentation-ready safety rating for appliance, automotive and battery pack audits, and a real requirement in EV and energy storage assemblies.
- Shore A 35 ± 8 low modulus, low stress – protects fragile components from thermal cycling and vibration stress; the elastomer expands and contracts with the assembly instead of fighting it.
- 1:1 mix ratio by weight with 11,000 ± 2,000 mPa·s mixed viscosity – easy manual or meter-mix dispensing, self-levelling into fine gaps and dense windings without voids.
- Room temperature or heat accelerated cure – 4–8 h at 25 °C, 30 min at 80 °C, or a two-stage cure (room temperature until tack-free, then 80 °C for 30 min) for the best balance of flow and final properties. No oven is mandatory, which matters on lines without heat capability.
- Pot life 60–180 min at 25 °C (100 g mix) – enough working time for multi-cavity potting and degassing without scrap.
- Excellent insulation – volume resistivity ≥ 1.0 × 1014 Ω·cm – withstands high voltage isolation requirements in EV, appliance and power supply assemblies.
- -40 °C to +200 °C service range – covers automotive under-hood, outdoor cabinets and continuous duty power conversion.
- Addition cure, no by-products – no corrosive or volatile release during cure, so no fogging on housings or corrosion of metal parts; the cured compound is re-enterable for repair in most designs.
- Factory-direct engineering support – ISO 9001 quality system, TDS / MSDS / COA per lot, custom viscosity, hardness and colour tuning, OEM / ODM and private label service.
Technical Data
Before mixing (uncured components)
| Property |
Test Method / Condition |
Unit |
Component A |
Component B |
| Appearance |
Visual |
— |
White liquid |
Grey liquid |
| Base Chemistry |
— |
— |
Polysiloxane |
Polysiloxane |
| Viscosity |
GB/T 2794 / 25 °C |
mPa·s |
10,500 ± 2,000 |
9,500 ± 2,000 |
| Density |
GB/T 13354 / 25 °C |
g/cm³ |
2.95 ± 0.02 |
2.95 ± 0.02 |
After mixing (A+B)
| Property |
Test Method / Condition |
Unit |
Value |
| Mix Ratio (A:B) |
By weight |
— |
1:1 |
| Mixed Viscosity |
25 °C |
mPa·s |
11,000 ± 2,000 |
| Mixed Density |
25 °C |
g/cm³ |
2.95 ± 0.02 |
| Pot Life / Operating Time |
25 °C / 100 g mix |
min |
60–180 |
| Cure Time (Room Temperature) |
25 °C |
h |
4–8 |
| Cure Time (Heat Accelerated) |
80 °C |
min |
30 |
Cured properties
| Property |
Test Method / Condition |
Unit |
Value |
| Appearance |
Visual |
— |
Grey elastomer |
| Hardness |
GB/T 531.1 |
Shore A |
35 ± 8 |
| Thermal Conductivity |
GB/T 38712-2020 |
W/m·K |
3.0 ± 0.1 |
| Volume Resistivity |
GB/T 31838.2-2019 / DC 500 V |
Ω·cm |
≥ 1.0 × 1014 |
| Flame Retardancy |
UL 94 |
Class |
V-0 |
| Operating Temperature Range |
— |
°C |
-40 to 200 |
All values are measured under standard conditions (25 °C, 50–60% RH) after the recommended cure schedule and are for reference only.
Recommended Curing Schedule
| Cure Option |
Condition |
Duration |
Notes |
| Room-temperature cure |
25 °C |
4–8 h |
Full cure at ambient temperature |
| Heat-accelerated cure |
80 °C |
30 min |
Fast cure; ensure even heating |
| Two-stage cure (recommended) |
RT until tack-free, then 80 °C |
30 min at 80 °C |
Best balance of flow and final properties |
Applications — Where HN-8830A/B Is Specified
- New energy vehicle and battery BMS – DC-DC converter potting, BMS board and battery module encapsulation, EV charger and charging pile power stages, motor controller housings, onboard charger assemblies.
- Power modules and power supplies – high power component potting and protection, switching power supplies, driver power supplies, IGBT and MOSFET module encapsulation, circuit board protection.
- Automotive electronics – automotive HID lamp power modules, ignition system power modules, sensor and controller housings.
- Home appliance and consumer electronics – home appliance controllers, inverter air conditioner modules, consumer electronics power boards.
- Energy storage and photovoltaic – energy storage system (ESS) module potting, PV inverter and solar inverter power stages.
- Lighting and industrial – LED driver and street light power modules, industrial power equipment, telecom and 5G power supplies.

Mixing and Potting Instructions
- Pre-mix – stir Component A thoroughly before use because fillers may settle during storage; shake or stir Component B to ensure homogeneity.
- Weighing – accurately weigh A and B by weight, not by volume, on a precision electronic scale at 1:1.
- Mixing – mix until the colour is uniform; scrape the container walls and bottom to ensure full dispersion and avoid introducing excessive air.
- Degassing (optional) – for void sensitive applications, degas under vacuum to remove air introduced during mixing.
- Pouring / potting – pour the mixed compound into the clean, dry device within the pot life; ensure complete coverage without trapped air.
- Curing – cure per the schedule above; do not move or stress the part during cure.
Cure inhibition warning (important): this addition-cure silicone may fail to cure in contact with organotin or tin-containing silicones, sulfur and polysulfide compounds, amines, polyurethane rubber, ammonia-containing items, phosphorus compounds, acidic substances and solder flux residues. Clean all substrates and tools free of these contaminants before use, and never mix it in contact with condensation-cure (acetoxy) silicone rubber, epoxy or polyurethane.
Packaging, Storage and Shelf Life
| Component |
Package Size |
Container Type |
Notes |
| Component A |
25 kg |
Plastic barrel |
— |
| Component B |
25 kg |
Plastic barrel |
— |
| Kit (A+B) |
50 kg / set |
— |
Standard supply set |
- Store in original, tightly sealed containers in a cool, dry, well ventilated area; recommended storage temperature 5–25 °C.
- Protect from direct sunlight, moisture and extreme temperatures.
- Shelf life: 6 months from date of manufacture when stored as recommended. Products past shelf life should be inspected and tested before use.
- Transportation: classified as non-dangerous goods (general chemicals). Handle with care to prevent leakage.
- Industrial / professional use only. Wear nitrile gloves, safety goggles and protective clothing; ensure adequate ventilation.
Quality System and Buyer Support
- ISO 9001 quality management with batch testing to GB/T 38712-2020, GB/T 531.1, GB/T 31838.2-2019 and UL 94 before every lot release.
- Documentation pack – TDS, MSDS and COA per lot for incoming inspection, customer audits and customs clearance; UL 94 V-0 and RoHS material statements available.
- Custom formulation – viscosity, hardness (Shore A), pot life, colour and conductivity tuned to your potting process by our FAE team.
- Process support – guidance on meter-mix equipment, degassing, cure schedule and cure inhibition troubleshooting for new lines.
- OEM / ODM and private label – your brand on the barrel, your label on the carton, your language on the documents.
- Export experience to Southeast Asia – Vietnam, Thailand, Indonesia, Malaysia, the Philippines and Singapore, with export packing, palletising and shipping documents prepared for factory receiving.
About this supplier
Shenzhen Hanast New Material Co., Ltd. is a premier high-tech enterprise and leading source manufacturer specializing in the R&D, manufacturing, and global supply of industrial silicone materials. As a strategic branch of the renowned Shenzhen Kanglibang Technology Co., Ltd., Hanast integrates over a decade of chemical adhesive expertise with a cutting-edge 40,000-square-meter modern production base (including our newly expanding Jiangmen facility) to deliver high-capacity, reliable material solutions worldwide.
We serve as a vital tier-one supplier and OEM/ODM partner for global factories, procurement managers, and engineering teams across diverse sectors, including electric vehicles (EV), battery energy storage systems (BESS), solar inverters, LED lighting, and industrial automation.

FAQ — Technical Questions Buyers Ask
Q1: What are the mix ratio, pot life and cure options for HN-8830A/B?
Mix 1:1 by weight (not by volume). Pot life is 60–180 minutes at 25 °C for a 100 g mix. Cure in 4–8 hours at room temperature, or 30 minutes at 80 °C, or use the recommended two-stage cure: room temperature until tack-free, then 80 °C for 30 minutes.
Q2: Why did my potting compound not cure, and how do I prevent it?
This is addition-cure (platinum) silicone, so it is sensitive to cure inhibitors: organotin or tin-containing silicones, sulfur and polysulfide compounds, amines, polyurethane rubber, ammonia, phosphorus compounds, acidic substances and solder flux residues. Clean substrates and tools thoroughly, avoid mixing in containers previously used for epoxy, polyurethane or acetoxy silicone, and always weigh A and B accurately at 1:1.
Q3: Is HN-8830A/B flame retardant and electrically insulating enough for battery and EV assemblies?
Yes. It is rated UL 94 V-0 with a volume resistivity of at least 1.0 × 1014 Ω·cm (GB/T 31838.2-2019, DC 500 V), and 3.0 ± 0.1 W/m·K thermal conductivity, which suits BMS boards, battery modules and DC-DC converters.
Q4: Will the low hardness protect fragile components during thermal cycling?
Shore A 35 ± 8 gives a low modulus, low stress elastomer that expands and contracts with the assembly instead of loading solder joints, ceramic capacitors and thin terminals. It also damps vibration, which is why it is used for automotive and BMS potting.
Q5: What are the MOQ, packaging, lead time and customization options?
Standard supply is a 50 kg set (Component A 25 kg + Component B 25 kg plastic barrels), minimum order 1 kg equivalent for trials, capacity 50 tons per month and 7–10 days lead time. Free samples, TDS, MSDS and COA are available, and we support custom viscosity, hardness and colour plus OEM, ODM and private label programs for Southeast Asian factories.
Overall Rating
Rating Snapshot
The following is the distribution of all ratingsAll Reviews