HN-8820A/B is a two-component, addition-cure silicone potting compound with 2.0 ± 0.1 W/m·K thermal conductivity and a mixed viscosity of only 5,000 to 8,000 mPa·s. That low viscosity is the reason it exists: it flows into cavities that a 3 W/m·K or 4 W/m·K paste cannot reach, wets fine gaps around connectors, terminals and coil windings, and self-levels without trapping air pockets at the bottom of a tall housing.
The cured elastomer is Shore A 45 to 50, harder than a low stress gel, which gives mechanical support to wound components and terminal blocks while still absorbing vibration and expansion. Electrical performance is strong: ≥ 5.0 × 10¹⁴ Ω·cm volume resistivity and UL 94 V-0 flame retardancy. Service range is -40 °C to 150 °C, with reliable waterproof, moisture-proof and anti-ageing behaviour for outdoor and humid installations.
Cure is flexible: 80 °C for 10 to 20 minutes on a heat-accelerated line, or room temperature cure for low volume and repair work. For factories in Vietnam, Thailand, Indonesia, Malaysia and the Philippines, HN-8820A/B ships as non-dangerous goods in 25 kg A and 25 kg B barrels or a 50 kg kit, with TDS, MSDS and a COA for every lot.
Where Low Viscosity Decides the Result| Filling challenge | Why 5,000 to 8,000 mPa·s helps | Typical part |
|---|---|---|
| Deep cavity, small opening | Low viscosity flows to the bottom before gelling, so the cavity fills from below without a void at the base | Tall power module housing, charger body, pole-mounted unit |
| Narrow gap between parts | Wets clearances around terminals, busbars and connector pins that a thick paste bridges over | Connector block, terminal assembly, sensor body |
| Long flow path | Reaches the far end of a long channel before the material starts to build viscosity | Cable joint, conduit, long module rail |
| Densely packed components | Penetrates between coils, cores and small components instead of sitting on top | Network transformer, solenoid, ignition module |
| Vacuum impregnation | Low viscosity and easy degassing make air removal practical | Wound components, sensors, potted PCBA |
| Thin wall housing | Self-levelling flow gives an even fill without pressure on thin walls | Outdoor enclosure, junction box, LED driver |
![]()
A potting compound is approved by several functions, each with a different concern. HN-8820A/B is documented so all of them can sign off.
Fewer voids and fewer rejected units in deep housings, plus one source factory for potting compound, thermal grease and silicone gel, so the material approval and the supply base stay short.
Clear terms: 1:1 mix by weight, 25 kg barrels or 50 kg kits, non-dangerous goods with no DG surcharge, TDS and MSDS for customs, COA per lot, and a 6 month shelf life so stock does not expire on the shelf.
Data for the process sheet: 2.0 ± 0.1 W/m·K, mixed viscosity 5,000 to 8,000 mPa·s, density 2.0 ± 0.02 g/cm³, Shore A 45 to 50, ≥ 5.0 × 10¹⁴ Ω·cm, UL 94 V-0, 80 °C cure in 10 to 20 minutes.
A predictable ramp: 50 kg kits for pilot builds, a documented degassing step for void-sensitive parts, and direct access to our Shenzhen engineers for fill volume, flow path and cure schedule checks.
A platform for the range: 2.0, 3.0 and 4.0 W/m·K grades plus silicone gel and thermal grease from one factory, so several product families share one supplier and one documentation set.
| Property | Test Method / Condition | Unit | Component A | Component B |
|---|---|---|---|---|
| Appearance | Visual | — | White liquid | Grey liquid |
| Base Chemistry | — | — | Polysiloxane | Polysiloxane |
| Viscosity | GB/T 2794 / 25 °C | mPa·s | 5,000 to 8,000 | 5,000 to 8,000 |
| Density | GB/T 13354 / 25 °C | g/cm³ | 2.0 ± 0.02 | 2.0 ± 0.02 |
| Property | Test Method / Condition | Unit | Value |
|---|---|---|---|
| Mix Ratio (A:B) | By weight | — | 1:1 |
| Mixed Viscosity | 25 °C | mPa·s | 5,000 to 8,000 |
| Cure Time (Heat Accelerated) | 80 °C | min | 10 to 20 |
| Cure at Room Temperature | 25 °C | — | Full cure at ambient, within the pot life stated on the lot TDS |
| Property | Test Method / Condition | Unit | Value |
|---|---|---|---|
| Appearance | Visual | — | Grey elastomer |
| Hardness | GB/T 531.1 | Shore A | 45 to 50 |
| Thermal Conductivity | GB/T 38712-2020 | W/m·K | 2.0 ± 0.1 |
| Volume Resistivity | GB/T 31838.2-2019 / DC 500 V | Ω·cm | ≥ 5.0 × 10¹⁴ |
| Flame Retardancy | UL 94 | Class | V-0 |
| Operating Temperature Range | — | °C | -40 to 150 |
All values are measured under standard conditions (25 °C, 50 to 60% RH) after the recommended cure schedule and are for reference only.
![]()
HN-8820A/B is specified wherever a cavity must be filled completely, thermally coupled and electrically insulated in one pour.
Battery modules, packs and BMS| Item | Detail |
|---|---|
| Packaging | Component A 25 kg plastic barrel, Component B 25 kg plastic barrel, kit A+B 50 kg per set |
| Mix ratio | 1:1 by weight |
| Minimum order quantity | 1 set (50 kg kit); smaller trial quantities on request |
| Delivery time | 3 to 5 working days for stock kits; 7 to 15 days for custom formulation or private label |
| Supply ability | 50 tons per month |
| Payment terms | T/T, L/C |
| Shelf life | 6 months from date of manufacture, stored as recommended |
| Storage | 5 to 25 °C, cool, dry, ventilated area, protected from sunlight, moisture and extreme temperature |
| Transport classification | Non-dangerous goods |
Products past their shelf life should be inspected and tested before use; do not use if appearance or viscosity has changed significantly.
HN-8820A/B is a two-component, 1:1 addition-cure silicone potting compound with 2.0 ± 0.1 W/m·K thermal conductivity and a mixed viscosity of 5,000 to 8,000 mPa·s. The low viscosity lets it flow into deep cavities through small openings, wet narrow gaps around terminals and connector pins, travel along long flow paths, and self-level into thin wall housings without trapping air at the base.
The cured material is a grey elastomer with Shore A 45 to 50 hardness, which gives mechanical support to wound components and terminal blocks while absorbing vibration. Volume resistivity is at least 5.0 × 10^14 Ω·cm, flame retardancy is UL 94 V-0, and the service range is -40 °C to 150 °C with waterproof, moisture-proof and anti-ageing performance.
Heat-accelerated cure takes 10 to 20 minutes at 80 °C, which suits an inline oven or heated fixture. The compound can also be cured at room temperature to full cure for low volume production, repair and field work; the working time and full cure at 25 °C follow the pot life stated on the lot TDS. A vacuum degassing step before pouring is recommended for void-sensitive parts.
It is used for BMS board potting and housing fill, battery module gap filling, pack junction box and high voltage distribution module encapsulation, OBC, DC-DC and motor controller modules, EV charger bodies and power modules, network and pulse transformers, solenoids, motor windings, inductors, LED drivers, power supplies, outdoor enclosures, cable joints and sensors.
Component A and Component B ship in 25 kg plastic barrels, or as a 50 kg A+B kit. The material is classified as non-dangerous goods, so no dangerous goods surcharge applies, and every lot ships with TDS, MSDS and COA. We regularly supply Vietnam, Thailand, Indonesia, Malaysia and the Philippines, with 3 to 5 working days for stock kits, 50 tons per month capacity, T/T or L/C terms and a 6 month shelf life stored at 5 to 25 °C.
Shenzhen Hanast New Materials Co., Ltd. is a China-based source factory for RTV-2 liquid silicone, potting compounds and thermal interface materials. Established in 2010 with a 40,000 m² production base, the company is an export-driven manufacturer with 70% to 80% of its business overseas, serving B2B clients that include ABB, Apple, Foxconn and BYD with OEM and ODM encapsulation and thermal management solutions.
Our range covers thermally conductive potting compounds from 2.0 to 4.0 W/m·K, silicone gels, thermal grease from 1.0 to 6.0 W/m·K and mould making rubber. Because potting compound, gel and grease for the same assembly come from one factory, your process engineers work with one technical contact and your purchasing team consolidates one supplier and one documentation set.
![]()
Send your housing drawing, cavity volume and component layout and our application engineers will confirm the grade, pour volume and degassing steps, and arrange a trial kit for your pilot build.
Overall Rating
Rating Snapshot
The following is the distribution of all ratingsAll Reviews