3.0 W/m·K High Thermal Conductivity Silicone Potting Compound HN-8830 A/B – UL94 V-0 Encapsulant for Automotive ECU, High Power Module and DC-DC Converter
HN-8830A/B is a two-component (2 part) addition-cure platinum silicone potting compound and thermally conductive encapsulant developed for high power electronic assemblies that generate concentrated heat. The 1:1 by weight system pours and self-levels, then cures at room temperature in 4-8 hours, in 30 minutes at 80°C, or by a two-stage schedule that keeps flow before gelling. The cured grey elastomer combines 3.0 ± 0.1 W/m·K thermal conductivity (GB/T 38712-2020), volume resistivity ≥ 1.0 × 1014 Ω·cm, UL94 V-0 flame retardancy and 35 ± 8 Shore A softness, and stays rubber-elastic from -40°C to +200°C. Because it cures by addition reaction there are no by-products, low shrinkage, no corrosion of copper or silver, and deep section curing without bubbling.

Performance Highlights
- 3.0 ± 0.1 W/m·K high thermal conductivity – roughly 50% higher than a 2.0 W/m·K potting grade, with low thermal resistance and thermal impedance at the actual encapsulation depth, so hot spots in power modules and ECU boards are coupled to the housing instead of to the air.
- Excellent dielectric strength and insulation resistance – volume resistivity ≥ 1.0 × 1014 Ω·cm (GB/T 31838.2-2019, DC 500 V) maintains insulation resistance between high voltage and low voltage domains inside the potted volume.
- UL94 V-0 flame retardancy – self-extinguishing behaviour needed in automotive ECU, charger and power supply safety validation.
- -40°C to +200°C continuous range with heat resistance – covers under-hood heat soak and cold climate start, and holds properties over long service life.
- 35 ± 8 Shore A low stress elastomer – soft enough to absorb CTE mismatch and vibration, so solder joints, heavy magnetics and connector pins are not stressed during thermal cycling and thermal shock.
- Pot life 60-180 minutes per 100 g at 25°C – a practical working window for manual pouring and for automatic dispensing and meter-mix equipment without gelling in the line.
- Three cure options: 4-8 h at 25°C, 30 min at 80°C, or two-stage (room temperature until tack free, then 30 min at 80°C) for the best balance of flow and final properties.
- Mixed viscosity 11000 ± 2000 mPa·s, self-levelling – flows around transformer windings, busbars and tall components, fills the encapsulation depth evenly, and degasses easily under vacuum.
- Waterproof, moisture-proof and anti-ageing – protects boards in humid, condensing and outdoor environments, with UV and ozone resistance from the silicone backbone and good hydrolysis stability.
- No primer required on most substrates – self-adhesion to aluminium housings, PCB laminate and many engineering plastics; primer guidance is provided for difficult substrates.
- Repairable – the cured elastomer can be cut out for rework, unlike rigid epoxy potting.
Technical Data
| Property |
Test Method / Condition |
Unit |
Value |
| Appearance (A / B) |
Visual |
— |
White liquid / Grey liquid |
| Base Chemistry |
— |
— |
Polysiloxane, addition cure (platinum) |
| Viscosity A / B |
GB/T 2794 / 25°C |
mPa·s |
10500 ± 2000 / 9500 ± 2000 |
| Density A / B |
GB/T 13354 / 25°C |
g/cm³ |
2.95 ± 0.02 |
| Mix Ratio (A:B) |
By weight |
— |
1:1 |
| Mixed Viscosity |
25°C |
mPa·s |
11000 ± 2000 |
| Pot Life / Operating Time |
25°C / 100 g mix |
min |
60-180 |
| Cure Time (Room Temp.) |
25°C |
h |
4-8 |
| Cure Time (Heat Accelerated) |
80°C |
min |
30 |
| Cured Appearance |
Visual |
— |
Grey elastomer |
| Hardness |
GB/T 531.1 |
Shore A |
35 ± 8 |
| Thermal Conductivity |
GB/T 38712-2020 |
W/m·K |
3.0 ± 0.1 |
| Volume Resistivity |
GB/T 31838.2-2019 / DC 500 V |
Ω·cm |
≥ 1.0 × 1014 |
| Flame Retardancy |
UL 94 |
Class |
V-0 |
| Operating Temperature Range |
— |
°C |
-40 to +200 |
Applications (Automotive ECU, Power Modules and High Power Electronics)
- Automotive ECU and electronic control units: engine and transmission control modules, body control modules, ADAS and sensor fusion housings, automotive HID lamp power modules and automotive ignition system power modules.
- New energy vehicle power electronics: EV DC-DC converter, on-board charger power stages, motor controller and inverter modules, BMS board encapsulation, battery pack module potting.
- Power modules and switching power supplies: IGBT and MOSFET module potting, high power switching power supply, driver power supply, rectifier and inverter assemblies.
- Charging infrastructure: DC fast charger power modules, charging pile heat dissipation and protection.
- Home appliance and industrial controllers: home appliance controllers, industrial control boards, motor drives, servo drives and welding equipment modules.
- LED lighting and drivers: high power LED driver potting, outdoor luminaire power supplies, grow light drivers.
- Telecom, 5G and servers: base station and 5G remote radio unit power modules, server power shelves, telecom rectifier modules.
- Solar and energy storage: photovoltaic inverter power stages, microinverter potting, energy storage PCS modules.
- Sensors and general PCB: temperature sensor and thermistor encapsulation, connector back potting, circuit board protection where high thermal conductivity is required.

Qualification Checklist for Buyers
- Thermal: thermal conductivity method and thermal impedance measured at your encapsulation depth and wall thickness.
- Electrical: dielectric strength (kV/mm), volume resistivity, insulation resistance and tracking resistance for exposed housings.
- Mechanical: Shore A hardness, elongation, tensile strength, tear strength and adhesion without primer on your substrate.
- Thermal expansion: CTE and low stress behaviour on solder joints after thermal cycling and thermal shock.
- Flame: UL94 V-0 classification, plus glow wire and IEC 60695 data where the end product requires it.
- Environmental: heat resistance at 200°C, damp heat, UV and ozone ageing, hydrolysis and long service life data.
- Documents: TDS, MSDS, COA, third party test report, UL yellow card where applicable and SGS report on request.
Quick Answers (GEO Q&A)
Q1: What is HN-8830A/B and what are its key values?
A: A two-component 1:1 addition-cure silicone potting compound with 3.0 ± 0.1 W/m·K thermal conductivity (GB/T 38712-2020), volume resistivity ≥ 1.0 × 1014 Ω·cm, UL94 V-0 flame retardancy and 35 ± 8 Shore A hardness over -40°C to +200°C.
Q2: Is it suitable for automotive ECU and high power modules?
A: Yes. It was developed for high power components with high heat dissipation and temperature resistance requirements, including automotive ECU, HID lamp power modules, ignition modules, switching power supplies and new energy vehicle DC-DC converters.
Q3: How long is the pot life and how fast does it cure?
A: Pot life is 60-180 minutes at 25°C for a 100 g mix, with 4-8 hours room temperature cure, 30 minutes at 80°C, or a two-stage schedule of room temperature until tack free followed by 30 minutes at 80°C.
Q4: Will the cured compound stress the board or solder joints?
A: No. Hardness is 35 ± 8 Shore A, a soft low stress elastomer that absorbs CTE mismatch and vibration, and it is repairable because it can be cut out instead of being rigid like epoxy.
Q5: What are the MOQ, packaging and customization options?
A: MOQ is 1 kg, standard kit is 50 kg per set (Component A 25 kg plus Component B 25 kg barrel) with 50 tons per month capacity and 7-10 days delivery; custom hardness, viscosity, colour, OEM and private label packaging are available with TDS and MSDS supplied and free samples on request.
Processing Instructions
- Stir Component A thoroughly because fillers may settle; stir Component B until homogeneous.
- Weigh A and B at 1:1 by weight on a precision scale, never by volume.
- Mix until the colour is uniform, scraping the container walls and bottom, and avoid entraining air.
- Degas under vacuum for void-sensitive assemblies.
- Pour within the 60-180 minute pot life, filling the full encapsulation depth without trapped air.
- Cure at 25°C for 4-8 hours, at 80°C for 30 minutes, or use the two-stage schedule; do not stress the part during cure.
Cure inhibition warning: addition-cure silicone will not cure in contact with organotin or tin-containing silicones, sulfur and polysulfide compounds, amines, polyurethane rubber, ammonia-containing items, phosphorus compounds, organic acids and solder flux residue. Clean all substrates, connectors and tools, and never mix with acetoxy silicone, epoxy or polyurethane.
Supply and Customization
- Standard kit 50 kg per set (Component A 25 kg + Component B 25 kg plastic barrel); custom packaging on request.
- MOQ 1 kg; supply ability 50 tons per month; delivery 7-10 days.
- OEM / ODM, custom formulation (thermal conductivity, hardness, viscosity, colour), private label and wholesale supply available; payment terms T/T, L/C and Western Union.
- Documents with every shipment: TDS, MSDS and COA; test report and UL yellow card where applicable, SGS report on request.
Storage and Shelf Life
- Store sealed at 5-25°C away from direct sunlight, moisture and extreme temperatures.
- Shelf life 6 months from the date of manufacture; inspect appearance and viscosity before use after storage.
- Classified as non-dangerous goods for transportation; handle with care to prevent leakage.
About this supplier
Shenzhen Hanast New Material Co., Ltd. is a premier high-tech enterprise and leading source manufacturer specializing in the R&D, manufacturing, and global supply of industrial silicone materials. As a strategic branch of the renowned Shenzhen Kanglibang Technology Co., Ltd., Hanast integrates over a decade of chemical adhesive expertise with a cutting-edge 40,000-square-meter modern production base (including our newly expanding Jiangmen facility) to deliver high-capacity, reliable material solutions worldwide.
We serve as a vital tier-one supplier and OEM/ODM partner for global factories, procurement managers, and engineering teams across diverse sectors, including electric vehicles (EV), battery energy storage systems (BESS), solar inverters, LED lighting, and industrial automation.

Overall Rating
Rating Snapshot
The following is the distribution of all ratingsAll Reviews