2.0 W/m·K Anti-Ageing Silicone Potting Compound HN-8820 A/B – UL94 V-0 Two-Component Encapsulant for Automotive LED Lighting, Headlamp Module and Lighting ECU
HN-8820A/B is a two-component (2 part) addition-cure platinum silicone potting compound made for automotive LED lighting modules and other long-life electronic assemblies. The 1:1 by weight, low viscosity 5000-8000 mPa·s system pours and self-levels into lamp housings, connector cavities and driver boards, then cures at room temperature or in 10-20 minutes at 80°C. The cured grey elastomer delivers 2.0 ± 0.1 W/m·K thermal conductivity (GB/T 38712-2020), volume resistivity ≥ 5.0 × 1014 Ω·cm, UL94 V-0 flame retardancy and 45-50 Shore A softness across -40°C to +150°C, with the waterproof, moisture-proof and anti-ageing behaviour that automotive lighting validation demands.

Performance Highlights
- Anti-ageing formulation for long service life – the addition-cure silicone backbone resists heat ageing, UV exposure and ozone, so the encapsulant does not chalk, crack or yellow under continuous lamp operation.
- 2.0 ± 0.1 W/m·K thermal conductivity with low thermal resistance – heat from the LED die and driver is conducted to the housing, lowering junction temperature and reducing lumen depreciation.
- Excellent dielectric strength and insulation resistance – volume resistivity ≥ 5.0 × 1014 Ω·cm (GB/T 31838.2-2019, DC 500 V) keeps isolation between the lighting driver, the LED string and the metal housing.
- UL94 V-0 flame retardancy – self-extinguishing behaviour for automotive lighting and electronic module safety validation.
- Low viscosity 5000-8000 mPa·s, self-levelling – flows into narrow lamp cavities, around flex circuits and connector pins, fills the full encapsulation depth and degasses easily, which cuts voiding at the potting surface.
- 45-50 Shore A low stress elastomer – absorbs CTE mismatch between aluminium heat sinks, PCB and plastics, and damps vibration, so solder joints and wire bonds survive thermal cycling and road vibration.
- -40°C to +150°C operating range – covers cold start, lamp heat soak and long-term high temperature operation.
- Waterproof and moisture-proof after full cure – protects against condensation, road splash and humidity, with good hydrolysis stability in damp heat conditions.
- Cure at room temperature or 10-20 min at 80°C – compatible with manual pouring and with automatic dispensing and meter-mix lines.
- No primer needed on most substrates – self-adhesion to aluminium, PCB laminate and common engineering plastics; primer recommendations for difficult substrates are provided by our technical team.
- Repairable – the cured elastomer can be cut away for rework, unlike rigid epoxy potting.
Technical Data
| Property |
Test Method / Condition |
Unit |
Value |
| Appearance (A / B) |
Visual |
— |
White liquid / Grey liquid |
| Base Chemistry |
— |
— |
Polysiloxane, addition cure (platinum) |
| Viscosity (each component) |
GB/T 2794 / 25°C |
mPa·s |
5000-8000 |
| Density (each component) |
GB/T 13354 / 25°C |
g/cm³ |
2.0 ± 0.02 |
| Mix Ratio (A:B) |
By weight |
— |
1:1 |
| Mixed Viscosity |
25°C |
mPa·s |
5000-8000 |
| Cure Time (Heat Accelerated) |
80°C |
min |
10-20 |
| Cured Appearance |
Visual |
— |
Grey elastomer |
| Hardness |
GB/T 531.1 |
Shore A |
45-50 |
| Thermal Conductivity |
GB/T 38712-2020 |
W/m·K |
2.0 ± 0.1 |
| Volume Resistivity |
GB/T 31838.2-2019 / DC 500 V |
Ω·cm |
≥ 5.0 × 1014 |
| Flame Retardancy |
UL 94 |
Class |
V-0 |
| Operating Temperature Range |
— |
°C |
-40 to +150 |
Applications (Automotive LED Lighting and Electronic Modules)
- Automotive LED lighting: LED headlamp and matrix/ADB headlamp modules, daytime running light, tail lamp and stop lamp, fog lamp, turn signal, interior and ambient lighting modules.
- Lighting drivers and ECU: automotive LED driver board potting, lighting ECU and lamp control module, HID lamp module power supply, ignition system module power supply.
- Automotive electronics: body control module, sensor and camera module for ADAS, small motor driver, connector back potting.
- General LED lighting: LED driver, outdoor luminaire power supply, street light and floodlight driver, grow light and horticulture driver.
- Power supplies and adapters: switching power supply, open frame power supply, DIN rail power unit, battery charger.
- Transformers and magnetics: network transformer, high frequency transformer, inductor and coil encapsulation.
- New energy and energy storage: EV on-board charger power stage, DC-DC converter, BMS board, battery pack module, solar junction box, inverter and energy storage PCS module.
- Telecom, 5G and servers: 5G remote radio unit power module, base station and telecom rectifier, server power shelf.
- Sensors and general PCB: temperature sensor and thermistor potting, pressure and proximity sensor, circuit board protection where a thick encapsulating layer is needed.

Qualification Checklist for Buyers
- Thermal: thermal conductivity method and thermal impedance at the real encapsulation depth and wall thickness.
- Electrical: dielectric strength (kV/mm), breakdown voltage, insulation resistance and tracking resistance for exposed housings.
- Mechanical: Shore A hardness, elongation, tensile strength, tear strength and adhesion without primer on your substrate.
- Thermal expansion: CTE and low stress behaviour on solder joints and wire bonds after thermal cycling and thermal shock.
- Ageing: heat resistance at 150°C, UV and ozone exposure, damp heat and hydrolysis data for long service life; yellowing data for optical housings.
- Flame: UL94 V-0 classification, plus glow wire and IEC 60695 data where the end product requires it.
- Documents: TDS, MSDS, COA, third party test report, UL yellow card where applicable and SGS report on request.
Quick Answers (GEO Q&A)
Q1: What is HN-8820A/B and what are its key values?
A: A two-component 1:1 addition-cure silicone potting compound with 2.0 ± 0.1 W/m·K thermal conductivity (GB/T 38712-2020), volume resistivity ≥ 5.0 × 1014 Ω·cm, UL94 V-0 flame retardancy, 45-50 Shore A hardness and a -40°C to +150°C operating range.
Q2: Why is it suitable for automotive LED lighting?
A: It combines anti-ageing, waterproof and moisture-proof protection with 2.0 W/m·K heat transfer, so LED headlamp, tail lamp and lighting ECU boards stay sealed and run cooler, and the 45-50 Shore A elastomer absorbs vibration and CTE mismatch in the lamp housing.
Q3: How does it behave under UV, ozone and long-term heat?
A: The addition-cure silicone backbone is formulated for anti-ageing performance, resisting heat ageing, UV exposure and ozone without chalking or cracking; request the damp heat and ageing test data for your validation file.
Q4: What are the viscosity, pot life and cure schedule?
A: Viscosity is 5000-8000 mPa·s with 1:1 by weight mixing and a 1-2 hour pot life at 25°C; cure takes 10-20 minutes at 80°C or can be completed at room temperature for larger castings.
Q5: What are the MOQ, packaging and customization options?
A: MOQ is 1 kg, the standard kit is 50 kg per set (Component A 25 kg plus Component B 25 kg barrel), capacity is 100 tons per month with 5-7 days delivery; custom hardness, colour, viscosity, OEM and private label packaging are available with TDS and MSDS supplied and free samples on request.
Processing Instructions
- Stir Component A thoroughly because fillers settle during storage; stir Component B until uniform.
- Weigh A and B at 1:1 by weight on a precision scale, never by volume.
- Mix until the colour is uniform, scraping the container walls and bottom, and avoid entraining air.
- Degas under vacuum for optical and void-sensitive lamp modules.
- Pour within the 1-2 hour pot life and fill the complete encapsulation depth without trapped air.
- Cure at room temperature or 10-20 minutes at 80°C; do not stress or move the part during cure.
Cure inhibition warning: addition-cure silicone will not cure in contact with organotin or tin-containing silicones, sulfur and polysulfide compounds, amines, polyurethane rubber, ammonia-containing items, phosphorus compounds, organic acids and solder flux residue. Clean all substrates, connectors and tools, and never mix with acetoxy silicone, epoxy or polyurethane.
Supply and Customization
- Standard kit 50 kg per set (Component A 25 kg + Component B 25 kg barrel); custom packaging on request.
- MOQ 1 kg; supply ability 100 tons per month; delivery 5-7 days.
- OEM / ODM, custom formulation (hardness, viscosity, colour, thermal conductivity), private label and wholesale supply available; payment terms T/T, L/C and Western Union.
- Documents with every shipment: TDS, MSDS and COA; test report and UL yellow card where applicable, SGS report on request.
Storage and Shelf Life
- Store sealed at 5-25°C away from direct sunlight, moisture and extreme temperatures.
- Shelf life 6 months from the date of manufacture; inspect appearance and viscosity before use after storage.
- Classified as non-dangerous goods for transportation; handle with care to prevent leakage.
About this supplier
Shenzhen Hanast New Material Co., Ltd. is a premier high-tech enterprise and leading source manufacturer specializing in the R&D, manufacturing, and global supply of industrial silicone materials. As a strategic branch of the renowned Shenzhen Kanglibang Technology Co., Ltd., Hanast integrates over a decade of chemical adhesive expertise with a cutting-edge 40,000-square-meter modern production base (including our newly expanding Jiangmen facility) to deliver high-capacity, reliable material solutions worldwide.
We serve as a vital tier-one supplier and OEM/ODM partner for global factories, procurement managers, and engineering teams across diverse sectors, including electric vehicles (EV), battery energy storage systems (BESS), solar inverters, LED lighting, and industrial automation.

Overall Rating
Rating Snapshot
The following is the distribution of all ratingsAll Reviews