Product Overview
HN100 is a single-component, non-curing, electrically insulating thermal conductive silicone grease. It holds its paste-like consistency during long-term use from -50 °C to +200 °C and combines excellent electrical insulation with good thermal conductivity. The compound has near-zero free radical content and resists extreme temperature, water, ozone and weathering, with low viscosity, good workability and stable performance in service.
Its defining value for design engineers is the combination of 1.0 ± 0.1 W/m·K thermal conductivity and a 2450 V/mm breakdown voltage at 0.20 mm (IEC 60243) — heat transfer and dielectric isolation in the same layer, which is what high voltage power stages, EV chargers and insulated heat sink assemblies need.
HN100 is safe, non-toxic, odourless, non-corrosive and RoHS 2.0 compliant. Typical buyers are B2B factories and brand owners — factory owners, purchasing managers, R&D engineers, project managers and product managers — in new energy vehicle electronics, power supplies, data centre equipment, photovoltaic and energy storage, home appliances, communications and LED lighting.

Why Factories and Engineering Teams Choose HN100
- 2450 V/mm dielectric strength at 0.20 mm (IEC 60243) – thermal path and electrical isolation in one material, for live power modules, high voltage assemblies and devices mounted on a common heat sink.
- 1.0 ± 0.1 W/m·K thermal conductivity (ASTM D5470) – repeatable, stable heat transfer for long duty power electronics where consistency matters more than a headline number.
- Non-curing, reworkable – never dries or hardens, so modules, heat sinks and devices can be dismounted, repaired and re-seated without re-pasting the assembly.
- -50 °C to +200 °C operating range – covers cold start, sealed enclosures, outdoor cabinets and continuous high temperature duty.
- Documented high temperature stability – no powdering after 8 days continuous baking at 200 °C and no drying after 3 hours at 280 °C on a 0.2 mm film, which supports thermal cycling validation.
- Low oil separation ≤ 0.3% and low volatility ≤ 0.6% at 200 °C / 24 h – controls pump-out and dry-out on vertical and vibration loaded interfaces and keeps nearby surfaces clean.
- Near-zero free radical content, water / ozone / weathering resistant – protects the silicone matrix against oxidation and embrittlement in humid, coastal and outdoor installations.
- Workability: 370 ± 20 (1/10 mm) penetration – brushing, rolling, screen printing, syringe and cartridge filling, and fully automatic dispensing lines.
- Factory-direct engineering support – ISO 9001 quality system, TDS / MSDS / COA with every shipment, custom formulation (conductivity, penetration, colour) and OEM / ODM / private label service.
- Material compatible – non-corrosive to aluminium, copper and nickel heat sinks, substrates and housings; non-toxic and odourless in normal industrial use.
Technical Data
| Property |
Test Method / Condition |
Unit |
Value |
| Appearance |
Visual inspection |
— |
White or grey paste |
| Thermal Conductivity |
ASTM D5470 |
W/m·K |
1.0 ± 0.1 |
| Specific Gravity |
GB/T 13354-1992 / 25 °C |
g/cm³ |
1.85 ± 0.08 |
| Oil Separation (Oil Bleed) |
SH/T 0324-1992 / 200 °C, 24 h |
% |
≤ 0.3 |
| Volatile Matter |
SH/T 0337-92 / 200 °C, 24 h |
% |
≤ 0.6 |
| Penetration (Cone Penetration) |
GB/T 269-2023 / 25 °C |
1/10 mm |
370 ± 20 |
| High-Temperature Stability |
200 °C constant-temperature oven, 0.2 mm film |
— |
No powdering after 8 days continuous baking |
| Temperature Resistance |
Heating platform, 280 °C, 0.2 mm film |
— |
No drying after 3 h continuous baking |
| Breakdown Voltage |
IEC 60243 / 0.20 mm thickness |
V/mm |
2450 |
| Operating Temperature Range |
— |
°C |
-50 to +200 |
| Compliance |
— |
— |
RoHS 2.0 |
All values are measured under standard conditions and are for reference only. Actual thermal performance may vary with application conditions, bond line thickness and contact pressure.
Applications — Where HN100 Is Specified
- New energy vehicle and EV electronics – onboard charger (OBC) stages, DC-DC converters, BMS boards, EV charger and charging pile power modules, motor controller interfaces and automotive electronics.
- Power semiconductors – power transistors, thyristors, rectifiers, power modules, solid state relays and regulated power supplies mounted on aluminium or copper heat sinks.
- Server, data centre and telecom – server power supplies, data centre heat sinks, 5G and network communication equipment, microwave devices, microwave communication and microwave transmission equipment.
- Photovoltaic and energy storage – PV inverter and solar inverter power stages, energy storage system (ESS) converters and battery module interfaces.
- Home appliance and consumer electronics – home appliance control boards, consumer electronics modules, CPU assemblies, LED lighting fixtures, LED driver boards and power supply modules.
- Sensors, heating and automotive parts – thermistors, temperature sensors, heating elements, printer heads, automotive electronics and automotive refrigerator modules.

Application Instructions
- Surface preparation – clean all contact surfaces with a solvent to remove grease, dust and oxidation; ensure surfaces are completely dry.
- Application – apply directly by brushing, rolling, automatic dispensing or screen printing.
- Spreading – transfer a small amount with a clean razor blade, plastic spatula or clean knife and spread evenly to the required thickness.
- Thickness control – the thinner the layer, the better the thermal transfer; excess paste can reduce efficiency. Wipe excess from the edges with a lint-free cloth.
- Assembly – assemble the heat sink and heat source immediately after application and torque fasteners to specification to control bond line thickness (BLT).
Packaging, Storage and Shelf Life
| Package Size |
Container Type |
Notes |
| 1 kg |
Plastic drum |
Standard package |
| 5 kg |
Plastic drum |
Standard package |
| Custom sizes |
— |
Syringe, cartridge and private label packaging available on request |
- Store in original, tightly sealed containers in a cool, dry, well ventilated area away from direct sunlight; recommended storage temperature below 27 °C.
- Shelf life: 12 months from date of manufacture when stored unopened and properly sealed.
- A small amount of silicone oil may separate during storage; this is normal. Stir thoroughly before use and performance is not affected.
- Transportation: classified as non-dangerous goods (general chemicals). Handle with care to prevent leakage.
- Industrial / professional use only. Wear nitrile gloves and safety goggles; ensure adequate ventilation and keep containers sealed when not in use.
Quality System and Buyer Support
- ISO 9001 quality management with in-house testing to ASTM D5470, IEC 60243, GB/T 269-2023, SH/T 0324-1992 and SH/T 0337-92 before every batch release.
- Documentation pack – TDS, MSDS and COA supplied with each shipment for incoming inspection, customer audits and customs clearance.
- Custom formulation – conductivity, penetration / viscosity, colour and oil bleed tuned to your drawing or dispense process by our FAE team.
- OEM / ODM and private label – your brand on the drum, your label on the carton, your language on the documents.
- Export experience to Southeast Asia – Vietnam, Thailand, Indonesia, Malaysia, the Philippines and Singapore, with export cartons, palletising and shipping documents prepared for factory receiving.
About this supplier
Shenzhen Hanast New Material Co., Ltd. is a premier high-tech enterprise and leading source manufacturer specializing in the R&D, manufacturing, and global supply of industrial silicone materials. As a strategic branch of the renowned Shenzhen Kanglibang Technology Co., Ltd., Hanast integrates over a decade of chemical adhesive expertise with a cutting-edge 40,000-square-meter modern production base (including our newly expanding Jiangmen facility) to deliver high-capacity, reliable material solutions worldwide.
We serve as a vital tier-one supplier and OEM/ODM partner for global factories, procurement managers, and engineering teams across diverse sectors, including electric vehicles (EV), battery energy storage systems (BESS), solar inverters, LED lighting, and industrial automation.

FAQ — Technical Questions Buyers Ask
Q1: Is HN100 electrically insulating and what is its breakdown voltage?
Yes. HN100 is an insulating thermal grease with a breakdown voltage of 2450 V/mm at 0.20 mm thickness tested to IEC 60243, combined with 1.0 ± 0.1 W/m·K thermal conductivity by ASTM D5470. It provides heat transfer and dielectric isolation in one layer.
Q2: What is the operating temperature range and does the grease dry out or powder?
HN100 runs from -50 °C to +200 °C and is non-curing, so it never hardens. In testing a 0.2 mm film shows no powdering after 8 days continuous baking at 200 °C and no drying after 3 hours at 280 °C. Oil separation is ≤ 0.3% and volatility ≤ 0.6% at 200 °C for 24 h.
Q3: Which industries and applications is HN100 used for?
Onboard charger (OBC) and BMS stages, EV charger and charging pile power modules, power transistors and thyristors, server power supplies and data centre heat sinks, 5G and microwave communication equipment, PV inverters, energy storage converters, home appliance control boards, LED drivers and sensors.
Q4: How does HN100 compare with a higher conductivity grade such as HN400 or HN500?
HN100 is the insulation-first grade: 2450 V/mm dielectric strength makes it the choice where the interface must isolate a live device from a grounded heat sink. HN400 (4 W/m·K) and HN500 (5 W/m·K metal-filled) trade dielectric strength for much higher conductivity and are specified for non-energised, non-exposed interfaces. Our engineers can help you choose based on your voltage and heat flux.
Q5: What are the MOQ, lead time, sample policy and customization options?
MOQ starts at 1 kilogram in 1 kg or 5 kg plastic drums, with 50 tons per month capacity and 3 to 5 working days delivery for standard drums. Free samples, TDS, MSDS and COA are available for evaluation, and we support custom formulation, OEM, ODM and private label programs for Southeast Asian factories.