Product Overview
HN100 is a single-component, non-curing, electrically insulating thermal conductive silicone grease with a controlled, low oil bleed formulation. It holds a stable paste consistency during long-term use from -50 °C to +200 °C, combines excellent electrical insulation with good thermal conductivity, and has near-zero free radical content with resistance to high and low temperature, water, ozone and weathering.
This grade is aimed at high volume assembly lines where cleanliness matters as much as conductivity: home appliance control boards, power adapters, LED drivers, consumer electronics modules and power supply units. Low oil separation (≤ 0.3%) and low volatility (≤ 0.6%) at 200 °C / 24 h keep the interface clean, avoid oil creeping onto nearby contacts and labels, and control pump-out on vertical or vibration loaded assemblies. The 2450 V/mm breakdown voltage at 0.20 mm keeps the same layer electrically insulating.
Typical buyers are B2B factories and brand owners — factory owners, purchasing managers, R&D engineers, project managers and product managers — sourcing for appliance, power supply, lighting and EV electronics production in Southeast Asia.

Why Factories and Engineering Teams Choose HN100
- Low oil bleed ≤ 0.3% at 200 °C / 24 h – the interface stays clean, no oil film creeping onto PCB contacts, connectors, labels or optics; the main complaint with low cost paste in appliance assembly.
- Low volatility ≤ 0.6% at 200 °C / 24 h – fewer volatiles inside sealed enclosures, no fogging on covers and lenses, stable long term performance.
- 2450 V/mm dielectric strength at 0.20 mm (IEC 60243) – thermal path and electrical isolation in one layer for live control boards, power adapters and insulated heat sink assemblies.
- 1.0 ± 0.1 W/m·K thermal conductivity (ASTM D5470) – matched to appliance and adapter heat loads, where a thin even film and clean interface beat an expensive high filler grade.
- Non-curing and reworkable – never dries or hardens, so boards and heat sinks can be repaired and re-seated on the production line without re-pasting.
- -50 °C to +200 °C range – covers cold storage and transport, sealed enclosures and continuous duty power supplies.
- Documented high temperature stability – no powdering after 8 days continuous baking at 200 °C and no drying after 3 hours at 280 °C on a 0.2 mm film.
- Workability: 370 ± 20 (1/10 mm) penetration – brushing, rolling, screen printing, syringe and cartridge filling, and high speed automatic dispensing lines.
- Bulk supply ready – 1 kg and 5 kg plastic drums, 50 tons per month capacity, ISO 9001 quality system, TDS / MSDS / COA per shipment, OEM / ODM and private label service.
Technical Data
| Property |
Test Method / Condition |
Unit |
Value |
| Appearance |
Visual inspection |
— |
White or grey paste |
| Thermal Conductivity |
ASTM D5470 |
W/m·K |
1.0 ± 0.1 |
| Specific Gravity |
GB/T 13354-1992 / 25 °C |
g/cm³ |
1.85 ± 0.08 |
| Oil Separation (Oil Bleed) |
SH/T 0324-1992 / 200 °C, 24 h |
% |
≤ 0.3 |
| Volatile Matter |
SH/T 0337-92 / 200 °C, 24 h |
% |
≤ 0.6 |
| Penetration (Cone Penetration) |
GB/T 269-2023 / 25 °C |
1/10 mm |
370 ± 20 |
| High-Temperature Stability |
200 °C constant-temperature oven, 0.2 mm film |
— |
No powdering after 8 days continuous baking |
| Temperature Resistance |
Heating platform, 280 °C, 0.2 mm film |
— |
No drying after 3 h continuous baking |
| Breakdown Voltage |
IEC 60243 / 0.20 mm thickness |
V/mm |
2450 |
| Operating Temperature Range |
— |
°C |
-50 to +200 |
| Compliance |
— |
— |
RoHS 2.0 |
All values are measured under standard conditions and are for reference only. Actual thermal performance may vary with application conditions, bond line thickness and contact pressure.
Applications — Where This HN100 Grade Is Specified
- Home appliance and consumer electronics – home appliance control boards, inverter air conditioner modules, refrigerator and washing machine boards, consumer electronics modules, CPU assemblies and set top box heat sinks.
- Power adapters and power supplies – adapter and charger heat sinks, switching power supply modules, regulated power supplies, power components and voltage regulators.
- LED and lighting – LED driver boards, LED lighting fixtures, street light and floodlight power modules, heat sink interfaces.
- New energy vehicle and EV electronics – onboard charger (OBC) auxiliary stages, EV charger and charging pile modules, BMS board cooling, automotive electronics and car refrigerator modules.
- Communications and microwave – microwave devices, microwave communication and transmission equipment, microwave power supplies, 5G and network communication equipment, server power supplies.
- Sensors and small devices – thermistors, temperature sensors, heating elements, printer heads and power transistor / thyristor heat sink interfaces.

Application Instructions
- Surface preparation – clean all contact surfaces with a solvent to remove grease, dust and oxidation; ensure surfaces are completely dry.
- Application – apply directly by brushing, rolling, automatic dispensing or screen printing.
- Spreading – transfer a small amount with a clean razor blade, plastic spatula or clean knife and spread evenly to the required thickness.
- Thickness control – the thinner the layer, the better the thermal transfer; excess paste can reduce efficiency. Wipe excess from the edges with a lint-free cloth.
- Assembly – assemble the heat sink and heat source immediately after application and torque fasteners to specification to control bond line thickness (BLT).
Packaging, Storage and Shelf Life
| Property |
Test Method / Condition |
Unit |
Value |
| 1 kg |
Plastic drum |
Standard package |
| 5 kg |
Plastic drum |
Standard package, suitable for volume line consumption |
| Custom sizes |
— |
Syringe, cartridge and private label packaging available on request |
- Store in original, tightly sealed containers in a cool, dry, well ventilated area away from direct sunlight; recommended storage temperature below 27 °C.
- Shelf life: 12 months from date of manufacture when stored unopened and properly sealed.
- A small amount of silicone oil may separate during storage; this is normal. Stir thoroughly before use and performance is not affected.
- Transportation: classified as non-dangerous goods (general chemicals). Handle with care to prevent leakage.
- Industrial / professional use only. Wear nitrile gloves and safety goggles; ensure adequate ventilation and keep containers sealed when not in use.
Quality System and Buyer Support
- ISO 9001 quality management with in-house testing to ASTM D5470, IEC 60243, GB/T 269-2023, SH/T 0324-1992 and SH/T 0337-92 before every batch release.
- Documentation pack – TDS, MSDS and COA supplied with each shipment for incoming inspection, customer audits and customs clearance.
- Batch consistency for volume lines – penetration and oil bleed are held inside a narrow window so dispense parameters do not need re-tuning between drums.
- Custom formulation – colour, penetration / viscosity and oil bleed tuned to your dispense process by our FAE team.
- OEM / ODM and private label – your brand on the drum, your label on the carton, your language on the documents.
- Export experience to Southeast Asia – Vietnam, Thailand, Indonesia, Malaysia, the Philippines and Singapore, with export cartons, palletising and shipping documents prepared for factory receiving.
About this supplier
Shenzhen Hanast New Material Co., Ltd. is a premier high-tech enterprise and leading source manufacturer specializing in the R&D, manufacturing, and global supply of industrial silicone materials. As a strategic branch of the renowned Shenzhen Kanglibang Technology Co., Ltd., Hanast integrates over a decade of chemical adhesive expertise with a cutting-edge 40,000-square-meter modern production base (including our newly expanding Jiangmen facility) to deliver high-capacity, reliable material solutions worldwide.
We serve as a vital tier-one supplier and OEM/ODM partner for global factories, procurement managers, and engineering teams across diverse sectors, including electric vehicles (EV), battery energy storage systems (BESS), solar inverters, LED lighting, and industrial automation.

FAQ — Technical Questions Buyers Ask
Q1: What does low oil bleed mean and why does it matter for appliance production?
Oil bleed (oil separation) is the amount of silicone oil that separates out of the paste. HN100 holds it at ≤ 0.3% at 200 °C for 24 h. In appliance and adapter assembly this prevents oil creeping onto PCB contacts, connectors, labels and lenses, and reduces pump-out on vertical interfaces.
Q2: Is HN100 insulating enough for a live control board or power adapter?
Yes. HN100 has a breakdown voltage of 2450 V/mm at 0.20 mm to IEC 60243, so the same layer transfers heat and provides dielectric isolation. Confirm your working voltage and creepage distance with our engineers before qualification.
Q3: What are the thermal conductivity and operating temperature range?
1.0 ± 0.1 W/m·K by ASTM D5470, with a working range of -50 °C to +200 °C. On a 0.2 mm film there is no powdering after 8 days at 200 °C and no drying after 3 hours at 280 °C.
Q4: Which industries and applications is this grade used for?
Home appliance control boards, inverter air conditioner and refrigerator modules, power adapters and switching power supplies, LED drivers and street light modules, EV charger and OBC auxiliary stages, BMS boards, microwave and 5G communication equipment, sensors and printer heads.
Q5: What are the MOQ, lead time, sample policy and customization options?
MOQ starts at 1 kilogram in 1 kg or 5 kg plastic drums, with 50 tons per month capacity and 3 to 5 working days delivery for standard drums. Free samples, TDS, MSDS and COA are available, and we support custom formulation, OEM, ODM and private label programs for Southeast Asian factories.