HN300 is a single-component, non-curing insulating thermal grease with a 2.5 ± 0.08 g/cm³ high filler loading, 2.95 ± 0.1 W/m·K thermal conductivity and 0.82 °C·cm²/W thermal resistance at 25 PSI, both measured to ASTM D5470. The filler loading is what makes it a production material rather than only a lab grade: a denser paste holds a thin, uniform film, resists slump and sag on vertical and inverted surfaces, and keeps the bond line repeatable from the first board to the ten-thousandth.
This grade is built for lines that print or dispense thermal grease at speed: stencil and screen printing with a squeegee, syringe and cartridge dispensing, and fully automatic robotic dispensing on power module, inverter and control board assembly. It stays printable through a shift, does not hard-slump in the stencil aperture, and does not hard-settle in the drum, so a drum pump or bulk handling system can feed the line without constant re-mixing.
For factories in Vietnam, Thailand, Indonesia, Malaysia and the Philippines, HN300 ships as non-dangerous goods in 1 kg and 5 kg plastic drums with TDS, MSDS and a COA for every lot, which keeps customs, warehouse storage and incoming inspection simple in hot and humid plants.
![]()
Most thermal grease failures on a production line are not conductivity failures. They are process failures: slump into a neighbouring area, an uneven film, a blocked stencil aperture, a paste that separates in the drum, or a bond line that drifts between shifts. HN300 is specified with those failure modes in mind.
| Process risk | What HN300 does | Why it matters on the line |
|---|---|---|
| Slump and sag on vertical parts | High filler loading with a 350 ± 20 penetration body that holds position | Paste stays where it is printed, so neighbouring pads and contacts are not contaminated |
| Uneven bond line between units | Dense, thixotropic paste spreads to a repeatable thin film under the same clamp force | Stable thermal resistance at 25 PSI, less unit to unit variation and fewer re-checks |
| Stencil aperture clogging and poor release | Fine, glossy paste with good workability for stencil and screen printing | Fewer stoppages and cleaning cycles, better first pass yield |
| Hard settling in the drum | Formulation resists hard settling; normal oil separation is ≤ 0.3% and is handled by stirring | Drum pump and bulk handling stay usable, no scrap drum at the end of a lot |
| Dry-out and crusting over time | Non-curing; no powdering after 8 days at 200 °C, no drying after 5 to 6 h at 280 °C | Field returns from interface degradation are reduced |
A process material is approved by several functions, each looking at a different risk. HN300 is documented so all of them can sign off.
Higher first pass yield and less scrap: a printable, slump-free paste reduces touch-up, rework and rejected modules, and one source factory covers grease, gel and potting compound for the same assembly.
Simple commercial terms: minimum order from 1 kg, stock in 3 to 5 working days, custom or private label in 7 to 15 days, T/T or L/C, TDS and MSDS for customs, COA per lot, non-dangerous goods with no DG surcharge.
Numbers to set the process around: 0.82 °C·cm²/W at 25 PSI, 2.95 ± 0.1 W/m·K, 2.5 ± 0.08 g/cm³ filler loading, 350 ± 20 penetration, 1850 V/mm dielectric strength, oil separation ≤ 0.3% and volatiles ≤ 0.7% at 200 °C / 24 h.
A predictable ramp: 1 kg trial drums for the first build, 7 to 15 days for custom viscosity or private label, and direct access to our Shenzhen application engineers for stencil design, dispense pattern and clamp force review.
One approved supplier across the range: the same silicone grease platform covers 1.0 to 6.0 W/m·K with insulating, low thermal resistance and high conductivity grades, so several module families share one material approval.
| Property | Test Method / Condition | Unit | Value |
|---|---|---|---|
| Appearance | Visual inspection | — | Grey, glossy, fine paste |
| Thermal Conductivity | ASTM D5470 | W/m·K | 2.95 ± 0.1 |
| Thermal Resistance | ASTM D5470 at 25 PSI | °C·cm²/W | 0.82 |
| Specific Gravity | GB/T 13354-1992 / 25 °C | g/cm³ | 2.5 ± 0.08 |
| Oil Separation (Oil Bleed) | SH/T 0324-1992 / 200 °C, 24 h | % | ≤ 0.3 |
| Volatile Matter | SH/T 0337-92 / 200 °C, 24 h | % | ≤ 0.7 |
| Penetration (Cone Penetration) | GB/T 269-2023 / 25 °C | 1/10 mm | 350 ± 20 |
| High-Temperature Stability | 200 °C constant-temperature oven, 0.2 mm film | — | No powdering after 8 days continuous baking |
| Temperature Resistance | Heating platform, 280 °C, 0.2 mm film | — | No drying after 5 to 6 h continuous baking |
| Breakdown Voltage | IEC 60243 / 0.20 mm thickness | V/mm | 1850 |
| Operating Temperature Range | — | °C | -40 to +180 |
| Curing Behaviour | — | — | Single component, non-curing |
| Compliance | — | — | RoHS 2.0 |
All values are measured under standard conditions and are for reference only. Actual thermal performance varies with application conditions, bond line thickness and contact pressure.
Application Method and Bond Line Guide| Method | Typical starting BLT | Line notes |
|---|---|---|
| Stencil printing | 0.05 to 0.10 mm | Keep apertures clear, check print definition at the start of each shift |
| Screen printing | 0.05 to 0.12 mm | Suitable for flat heat spreaders and large area plates |
| Syringe or cartridge dispensing | 0.08 to 0.15 mm | Use a dispense pattern that covers the full die area after clamping |
| Automatic robotic dispensing | 0.08 to 0.20 mm | Fix dot height and clamp force, then audit the film on first-off samples |
| Roller or brush (repair) | 0.10 to 0.20 mm | For rework and low volume assembly, wipe excess from edges |
![]()
HN300 is specified wherever a printed or dispensed film must stay thin, stay put and stay stable over years of service.
Power modules and industrial power electronicsYes. HN300 is a fine, glossy paste with 2.5 ± 0.08 g/cm³ high filler loading and 350 ± 20 (1/10 mm) penetration, designed to release cleanly from stencil and screen apertures and to hold its shape without slumping into adjacent areas. It prints a thin film in the 0.05 to 0.12 mm range depending on the method, and it does not harden, so printed paste stays workable through normal line handling before clamping.
Thermal conductivity is 2.95 ± 0.1 W/m·K and thermal resistance is 0.82 °C·cm²/W at 25 PSI, both tested to ASTM D5470. The resistance value is measured under clamp pressure, so it reflects what the interface does on a real assembly. Specific gravity is 2.5 ± 0.08 g/cm³, breakdown voltage is 1850 V/mm at 0.20 mm, and the operating range is -40 °C to +180 °C.
The formulation resists hard settling, which matters for drum pumps and automated feeding systems. Normal oil separation is at or below 0.3% after 200 °C for 24 hours testing, and a small amount of silicone oil may appear on the surface during storage; this is normal for a non-curing grease and is handled by stirring before use. Volatile matter is at or below 0.7%, so the paste does not dry out in the container.
HN300 is used on IGBT and SiC module base plates, inverter and servo drives, power supplies, solid state relays, traction inverters, OBC, DC-DC converters, BMS boards, battery modules, EV chargers, energy storage cabinets, PCS, PV inverters, servers, CPU and GPU retainers, heat pipes, vapour chambers, 5G telecom equipment, LED drivers, home appliance control boards and temperature sensors.
Yes, we regularly ship HN300 to Vietnam, Thailand, Indonesia, Malaysia and the Philippines and to other Southeast Asian destinations on request. It is classified as non-dangerous goods, so no DG surcharge applies, and it travels in 1 kg or 5 kg plastic drums on pallets. Minimum order is 1 kg, stock drums ship in 3 to 5 working days, custom or private label orders take 7 to 15 days, capacity is 50 tons per month, payment is T/T or L/C, and every lot ships with TDS, MSDS and COA.
Shenzhen Hanast New Materials Co., Ltd. is a China-based source factory for RTV-2 liquid silicone, potting compounds and thermal interface materials. Established in 2010 with a 40,000 m² production base, the company is an export-driven manufacturer with 70% to 80% of its business overseas, serving B2B clients that include ABB, Apple, Foxconn and BYD with OEM and ODM encapsulation and thermal management solutions.
Our thermal range covers silicone grease from 1.0 to 6.0 W/m·K, including insulating, low thermal resistance and high filler grades, plus thermally conductive potting compounds and silicone gels. Because grease, gel and potting compound for the same module come from one factory, your process engineers work with one technical contact and your purchasing team consolidates one supplier, one documentation set and one shipment schedule.
![]()
Send your stencil design or dispense pattern and our application engineers will confirm the grade, print window and clamp force, and arrange a 1 kg sample drum for your line trial.