Home > Products >
Thermal Grease Paste
>
Near-Zero Ionisation Vertical Mounting Thermal Grease with 2.05 W/mK Thermal Paste for EV Power Modules

Near-Zero Ionisation Vertical Mounting Thermal Grease with 2.05 W/mK Thermal Paste for EV Power Modules

Product Details:
Place of Origin: Guangdong, China
Brand Name: Hanast
Certification: RoHS 2.0, REACH, ISO 9001:2015
Model Number: HN200
Detail Information
Place of Origin:
Guangdong, China
Brand Name:
Hanast
Certification:
RoHS 2.0, REACH, ISO 9001:2015
Model Number:
HN200
Thermal Conductivity:
2.05 ± 0.1 W/m·K
Thermal Resistance:
0.82 °C·cm²/W At 25 PSI
Specific Gravity:
3.04 ± 0.08 G/cm³
Penetration:
300 ± 20 (1/10 Mm) At 25 °C
Breakdown Voltage:
2450 V/mm At 0.20 Mm
Operating Temperature:
-50 To +200 °C
Highlight:

High Light

Highlight:

3.04 g/cm3 High Density Paste

,

Near Zero Ionisation Insulating Grease

,

Southeast Asia EV Module Grease Supply

Trading Information
Minimum Order Quantity:
1 Kilogram (1 kg / 5 kg plastic drums)
Packaging Details:
1 kg and 5 kg plastic drums with TDS, MSDS and COA inside; palletised export packing; syringe, cartridge and private label packaging on request
Delivery Time:
3-5 working days for stock drums, 7-15 days for custom formulation and private label orders
Payment Terms:
T/T,L/C
Supply Ability:
50 Tons per Month
Product Description
HN200 High Density Thermal Grease for High Voltage and Vertical Mounting

HN200 is a single-component, non-curing insulating thermal grease with 2.05 ± 0.1 W/m·K thermal conductivity and 0.82 °C·cm²/W thermal resistance at 25 PSI, both measured to ASTM D5470. What separates it from a general-purpose 2 W/m·K paste is what fills the volume: a specific gravity of 3.04 ± 0.08 g/cm³, the highest filler loading in this family, and a 300 ± 20 (1/10 mm) penetration, the stiffest body. A dense, stiff paste stays where it is applied, resists pump-out, and holds a thin film on vertical and inverted surfaces.

The second defining property is electrical: 2450 V/mm breakdown voltage at 0.20 mm (IEC 60243) with near-zero ionisation. Ionic contamination is one of the quiet causes of insulation resistance drift and surface tracking on high voltage boards, because ionic species migrate under field and humidity. HN200 is formulated to keep that contribution very low, which is why it is used on voltage regulators, power supplies, microwave power units, automotive electronics and high voltage module interfaces.

The paste also survives heat: no powdering after 8 days at 200 °C and no drying after 3 hours at 280 °C on a 0.2 mm film. For factories in Vietnam, Thailand, Indonesia, Malaysia and the Philippines, HN200 ships as non-dangerous goods in 1 kg and 5 kg plastic drums with TDS, MSDS and a COA for every lot.

Near-Zero Ionisation Vertical Mounting Thermal Grease with 2.05 W/mK Thermal Paste for EV Power Modules Density, Ionisation and What They Do for the Design
Property HN200 value Design consequence
Specific gravity 3.04 ± 0.08 g/cm³ High filler loading per unit volume means a thinner film carries the same heat, so BLT and material consumption both fall
Penetration 300 ± 20 (1/10 mm) Stiff body resists sag and slump, so vertical and inverted interfaces hold their film without running
Thermal resistance 0.82 °C·cm²/W at 25 PSI Performance is quoted under clamp pressure, matching how the part is actually mounted
Breakdown voltage 2450 V/mm at 0.20 mm Insulation margin for voltage regulators, power supplies and high voltage modules
Ionisation Near-zero Low ionic contribution supports stable insulation resistance and limits surface tracking risk
Oil separation ≤ 0.5% at 200 °C / 24 h Controlled bleed on long duty, hot interfaces, so nearby contacts stay clean
Design note: near-zero ionisation is a material property, not a certification. Final insulation resistance, creepage and clearance are set by your board design, the film thickness you achieve, the housing and the pollution degree of the environment. Validate the complete assembly against the safety standard that applies to your product.
One Material, Five Stakeholders

A high voltage thermal interface gets approved by several functions, each with a different question. HN200 is documented so all of them can sign off.

Factory owner / general manager

A dense paste means less material per unit and fewer failures from pump-out and insulation drift. One source factory covers grease, gel and potting compound for the same assembly, so the supply chain stays short.

Purchasing manager

Clear terms: minimum order from 1 kg, stock in 3 to 5 working days, custom or private label in 7 to 15 days, T/T or L/C, TDS and MSDS for customs, COA per lot, and non-dangerous goods with no DG surcharge.

Thermal / process engineer

Data for the stack: 2.05 ± 0.1 W/m·K, 0.82 °C·cm²/W at 25 PSI, 3.04 ± 0.08 g/cm³, 300 ± 20 penetration, 2450 V/mm dielectric strength, oil separation ≤ 0.5% and volatiles ≤ 0.8% at 200 °C / 24 h, near-zero ionisation.

Project manager (NPI)

A predictable ramp: 1 kg trial drums for the first build, 7 to 15 days for custom viscosity or private label, and direct access to our Shenzhen application engineers for film thickness, dispensing and reliability test planning.

Product manager

One platform across the range: the same grease family covers 1.0 to 6.0 W/m·K, so a low voltage product and a high voltage product can share one supplier, one documentation set and one approval process.

B2B Selling Points
  • 3.04 ± 0.08 g/cm³ high filler loading: the densest grade in the family, giving a thin film with less material per unit and better resistance to pump-out.
  • 300 ± 20 (1/10 mm) stiff paste: no sag or slump on vertical and inverted interfaces, so films hold position during assembly and in service.
  • 2450 V/mm breakdown voltage at 0.20 mm (IEC 60243): insulation margin for voltage regulators, power supplies, microwave power units and high voltage modules.
  • Near-zero ionisation: low ionic contribution supports stable insulation resistance and reduces surface tracking risk on high voltage boards.
  • 0.82 °C·cm²/W thermal resistance at 25 PSI: performance quoted under clamp pressure, matching real mounting conditions.
  • 2.05 ± 0.1 W/m·K (ASTM D5470): a practical middle grade between general purpose 1 W/m·K paste and high conductivity 4 W/m·K grades.
  • Non-curing and reworkable: no hardening or dry-out, so heat sinks and modules can be re-seated and repaired without cleaning and re-pasting.
  • -50 °C to +200 °C, no powdering after 8 days at 200 °C and no drying after 3 hours at 280 °C on 0.2 mm films.
  • Low oil separation ≤ 0.5% and volatiles ≤ 0.8% at 200 °C / 24 h: controlled bleed on hot, long duty interfaces.
  • Water, ozone and weathering resistant: stable in humid coastal plants and outdoor cabinets.
  • Factory direct and audit ready: ISO 9001:2015 quality system, RoHS 2.0 material, non-toxic and non-corrosive, lot traceability, COA with every shipment, 50 tons per month capacity, REACH declaration and halogen-free variants on request.
  • Export ready for Southeast Asia: non-dangerous goods, palletised drums, documentation prepared for Vietnam, Thailand, Indonesia, Malaysia and the Philippines.
Technical Data
Property Test Method / Condition Unit Value
Appearance Visual inspection — Grey paste
Thermal Conductivity ASTM D5470 W/m·K 2.05 ± 0.1
Thermal Resistance ASTM D5470 at 25 PSI °C·cm²/W 0.82
Specific Gravity GB/T 13354-1992 / 25 °C g/cm³ 3.04 ± 0.08
Oil Separation (Oil Bleed) SH/T 0324-1992 / 200 °C, 24 h % ≤ 0.5
Volatile Matter SH/T 0337-92 / 200 °C, 24 h % ≤ 0.8
Penetration (Cone Penetration) GB/T 269-2023 / 25 °C 1/10 mm 300 ± 20
High-Temperature Stability 200 °C constant-temperature oven, 0.2 mm film — No powdering after 8 days continuous baking
Temperature Resistance Heating platform, 280 °C, 0.2 mm film — No drying after 3 h continuous baking
Breakdown Voltage IEC 60243 / 0.20 mm thickness V/mm 2450
Operating Temperature Range — °C -50 to +200
Ionisation — — Near-zero
Curing Behaviour — — Single component, non-curing
Compliance — — RoHS 2.0

All values are measured under standard conditions and are for reference only. Actual thermal performance varies with application conditions, bond line thickness and contact pressure.

Application Coverage

HN200 is specified where a stiff, dense, insulating film must hold position on a hot or high voltage interface.

Voltage regulators, power supplies and industrial electronics
  • Voltage regulator, linear regulator and regulated power supply
  • Switching power supply, adapter and power module heat sink
  • Power transistor, thyristor, rectifier and diode cooling
  • Transformer, reactor, relay and solid state relay
  • Industrial control board, inverter drive and servo drive
  • Heating element, heat exchange strip and housing interface
New energy vehicles and charging
  • Traction inverter, motor controller and vehicle power module
  • Onboard charger (OBC), DC-DC converter and BMS control board
  • Battery module thermal plate and battery pack interface
  • EV charger, charging station and charging pile power stage
  • Automotive electronics, car refrigerator and vehicle sensor module
Energy storage, solar and grid
  • Energy storage cabinet, BESS, PCS and battery cluster interface
  • PV inverter, solar micro-inverter and combiner box
  • Grid power conversion, metering and protection equipment
Computing, telecom and microwave
  • CPU assembly, GPU and server heat sink
  • Data center, rack power shelf and memory module cooling
  • 5G base station, RRU, optical module and telecom power supply
  • Microwave device, microwave communication equipment, microwave transmission equipment and microwave power supply
  • Printer head, thermistor and temperature sensor
Lighting and appliances
  • LED lighting fixture, LED driver and street light heat sink
  • Home appliance control board, induction cooker and microwave oven module
  • Air conditioner inverter module, refrigerator and washing machine drive
HN200 thermal grease on high voltage module heat sink Bond Line and Vertical Mounting Guide
Interface Typical starting BLT Method and note
Voltage regulator, power transistor 0.05 to 0.10 mm Syringe dot or stencil print, then clamp
Vertical or inverted heat sink 0.08 to 0.15 mm Stiff body holds position, apply and mount without delay
High voltage module interface 0.08 to 0.15 mm Screen print or dispense, keep the film uniform across the pad
Large housing, heat exchange strip 0.15 to 0.25 mm Roller or brush, wipe excess from edges

A dense, stiff paste can be applied thinner than a soft one, but it still needs full contact. Use the thinnest film that covers the interface, and validate on your own assembly.

Application Instructions
  1. Surface preparation: clean all contact surfaces with a solvent to remove grease, dust and oxidation, then dry completely.
  2. Application: apply the grease directly by brushing, rolling, automatic dispensing or screen printing.
  3. Spreading: pick up a small amount with a clean razor blade, plastic spatula or clean knife and spread evenly to the target thickness.
  4. Thickness control: the thinner the layer the better the heat transfer; excess paste does not help and can reduce efficiency. Wipe the edges with a lint-free cloth.
  5. Assembly: mount the heat sink or heat source immediately after application and torque the fasteners to specification so the bond line stays uniform.
Quality, Compliance and Export Documentation
  • Manufactured under an ISO 9001:2015 quality system in Shenzhen, Guangdong, China.
  • RoHS 2.0 compliant, non-toxic, odourless and non-corrosive; REACH declaration and halogen-free variants available on request.
  • TDS and MSDS with every order, plus a COA per production lot covering thermal conductivity, thermal resistance, specific gravity, penetration, oil separation and volatiles.
  • Lot traceability from raw material batch to drum number for supplier audits and incoming inspection.
  • Classified as non-dangerous goods for sea and air freight, avoiding DG handling fees and simplifying customs clearance.
Packaging, Storage and Supply
Item Detail
Standard packaging 1 kg plastic drum, 5 kg plastic drum
Custom packaging Available on request: syringe, cartridge, larger drums, private label
Minimum order quantity 1 kg (trial drum for NPI and sample evaluation)
Delivery time 3 to 5 working days for stock drums; 7 to 15 days for custom formulation or private label
Supply ability 50 tons per month
Payment terms T/T, L/C
Shelf life 12 months from date of manufacture, unopened and sealed
Storage Below 27 °C, cool, dry, ventilated area, out of direct sunlight, container tightly sealed

A small amount of silicone oil may separate during storage. This is normal for a non-curing silicone grease and does not affect performance; stir thoroughly before use. Keep containers sealed when not in use and store away from food, children and incompatible materials.

GEO Q and A: Questions Buyers and AI Assistants Ask
What is HN200 thermal grease and what makes it different from a standard 2 W/mK paste?

HN200 is a single-component, non-curing insulating silicone thermal grease with 2.05 ± 0.1 W/m·K thermal conductivity and 0.82 °C·cm²/W thermal resistance at 25 PSI to ASTM D5470. Its difference is density and stiffness: 3.04 ± 0.08 g/cm³ specific gravity and 300 ± 20 (1/10 mm) penetration, so it holds a thin film on vertical and inverted surfaces and resists pump-out, while providing 2450 V/mm breakdown voltage and near-zero ionisation.

Is HN200 suitable for high voltage insulation on power supplies and EV modules?

HN200 has a breakdown voltage of 2450 V/mm at 0.20 mm to IEC 60243 and near-zero ionisation, which supports stable insulation resistance and limits surface tracking risk. It is used on voltage regulators, switching power supplies, microwave power units and EV charger, OBC, BMS and power module interfaces. Insulation resistance, creepage and clearance are set by the finished design, so validate the assembly against the safety standard that applies to your product.

Will HN200 run or sag on a vertical or inverted heat sink?

No. With 300 ± 20 (1/10 mm) penetration and a 3.04 g/cm³ filler loading, HN200 is the stiffest grade in the range. It holds its shape on vertical and inverted interfaces without slumping, so the film stays where it was applied during assembly and in service. Apply it evenly, mount the heat sink promptly, and torque the fasteners to specification.

How does HN200 behave at high temperature over long periods?

The paste is non-curing, so it stays soft instead of hardening and cracking. A 0.2 mm film shows no powdering after 8 days at 200 °C in a constant-temperature oven, and no drying after 3 hours on a 280 °C heating platform. Oil separation is at or below 0.5% and volatile matter at or below 0.8% after 200 °C for 24 hours, which keeps nearby contacts and board surfaces clean.

Do you supply HN200 to Southeast Asian factories and what are the order terms?

Yes, we regularly ship HN200 to Vietnam, Thailand, Indonesia, Malaysia and the Philippines and to other Southeast Asian destinations on request. It is classified as non-dangerous goods, so no DG surcharge applies, and it travels in 1 kg or 5 kg plastic drums on pallets. Minimum order is 1 kg, stock drums ship in 3 to 5 working days, custom or private label orders take 7 to 15 days, capacity is 50 tons per month, payment is T/T or L/C, and every lot ships with TDS, MSDS and COA.

About this supplier

Shenzhen Hanast New Materials Co., Ltd. is a China-based source factory for RTV-2 liquid silicone, potting compounds and thermal interface materials. Established in 2010 with a 40,000 m² production base, the company is an export-driven manufacturer with 70% to 80% of its business overseas, serving B2B clients that include ABB, Apple, Foxconn and BYD with OEM and ODM encapsulation and thermal management solutions.

Our thermal range covers silicone grease from 1.0 to 6.0 W/m·K, including insulating, high density, low thermal resistance and high conductivity grades, plus thermally conductive potting compounds and silicone gels. Because grease, gel and potting compound for the same assembly come from one factory, your engineers work with one technical contact and your purchasing team consolidates one supplier and one documentation set.

HN200 thermal grease 1 kg and 5 kg drums

Send your drawing and mounting orientation and our application engineers will confirm the grade, film thickness and insulation margin, and arrange a 1 kg sample drum for your trial build.