Home > Products >
Thermally Conductive Potting Compound
>
3.0 W/mK UL94 V-0 Self-Leveling Thermally Conductive Potting Compound Thermal Potting Silicone for Battery Module Potting

3.0 W/mK UL94 V-0 Self-Leveling Thermally Conductive Potting Compound Thermal Potting Silicone for Battery Module Potting

Product Details:
Place of Origin: Guangdong, China
Brand Name: Hanast
Certification: UL 94 V-0, RoHS 2.0, ISO 9001:2015
Model Number: HN-8830A/B
Detail Information
Place of Origin:
Guangdong, China
Brand Name:
Hanast
Certification:
UL 94 V-0, RoHS 2.0, ISO 9001:2015
Model Number:
HN-8830A/B
Thermal Conductivity:
3.0 ± 0.1 W/m·K
Mixed Viscosity:
11,000 ± 2,000 MPa·s At 25 °C
Mix Ratio:
1:1 By Weight
Hardness:
Shore A 35 ± 8
Volume Resistivity:
≥ 1.0 × 10^14 Ω·cm
Operating Temperature:
-40 To +200 °C
Highlight:

High Light

Highlight:

Prismatic Pouch Module Potting Silicone

,

CTP Battery Pack 3.0 W/mK Compound

,

Southeast Asia BMS Potting Supply

Trading Information
Minimum Order Quantity:
1 set (50 kg A+B kit)
Packaging Details:
Component A 25 kg plastic barrel, Component B 25 kg plastic barrel, A+B kit 50 kg per set; palletised export packing; private label on request
Delivery Time:
3-5 working days for stock kits, 7-15 days for custom formulation and private label orders
Payment Terms:
T/T,L/C
Supply Ability:
50 Tons per Month
Product Description
HN-8830A/B Thermal Potting Silicone for Prismatic and Pouch Battery Modules

HN-8830A/B is a two-component, addition-cure (platinum-catalysed) silicone potting compound with 3.0 ± 0.1 W/m·K thermal conductivity, UL 94 V-0 flame retardancy and ≥ 1.0 × 10¹⁴ Ω·cm volume resistivity. It mixes 1:1 by weight, flows at 11,000 ± 2,000 mPa·s and self-levels, so it fills a module cavity evenly without hand spreading or vibration, and it cures to a Shore A 35 ± 8 elastomer that absorbs thermal expansion instead of stressing the cells and busbars around it.

The working range is -40 °C to +200 °C. Room temperature cure takes 4 to 8 hours; a heat-accelerated cure at 80 °C takes 30 minutes; and a two-stage schedule (room temperature until tack-free, then 30 minutes at 80 °C) gives the best balance of flow and final properties. Operating time is 60 to 180 minutes for a 100 g mix, which is enough to pot a multi-cell module or a deep housing in one pour.

For factories in Vietnam, Thailand, Indonesia, Malaysia and the Philippines, HN-8830A/B ships as non-dangerous goods in 25 kg A and 25 kg B barrels, or as a 50 kg kit, with TDS, MSDS and a COA for every lot. The kit format matches meter-mix and static-mixer dispensing lines, so the same drum can feed a manual bench or an automated potting cell.

Why This Grade Fits Battery Modules and BMS Housings
Requirement in a battery module HN-8830A/B behaviour Practical effect
Heat spreading from cells and busbars 3.0 ± 0.1 W/m·K, tested to GB/T 38712-2020 Reduces local hot spots and temperature spread across the pack
Filling a closed cavity with small gaps 11,000 ± 2,000 mPa·s, self-levelling, 1:1 mix Flows around cell holders, sense wires and cooling plates without voids
No mechanical stress on cells and welds Shore A 35 ± 8 elastomer Absorbs expansion and vibration instead of transferring stress to joints
Flame and safety requirements UL 94 V-0 Supports the flame rating of the finished module
Electrical isolation ≥ 1.0 × 10¹⁴ Ω·cm volume resistivity Insulation between cells, busbars and housing
Thermal cycling and hot environments -40 °C to +200 °C, elastic after cure Stays rubbery through cycling instead of cracking
Production time per module 60 to 180 min operating time, 80 °C / 30 min cure Long enough to pot large cavities, short enough for line throughput

HN-8830A/B thermal potting silicone grey compound

One Material, Five Stakeholders

A potting decision is signed off by several functions, each with a different risk. HN-8830A/B is documented so all of them can approve it.

Factory owner / general manager

Fewer rejects from voids, incomplete fill and cracked modules, and one source factory for potting compound, thermal grease and silicone gel, so the material approval and the supply chain stay short.

Purchasing manager

Clear terms: 1:1 mix reduces weighing errors, 25 kg barrels or 50 kg kits, non-dangerous goods with no DG surcharge, TDS and MSDS for customs, COA per lot, and 6 months shelf life so stock does not expire on the rack.

Thermal / process engineer

Data for the process sheet: 3.0 ± 0.1 W/m·K, 11,000 ± 2,000 mPa·s mixed, 2.95 ± 0.02 g/cm³, 60 to 180 min pot life at 25 °C, RT 4 to 8 h or 80 °C 30 min cure, Shore A 35 ± 8, UL 94 V-0, ≥ 1.0 × 10¹⁴ Ω·cm.

Project manager (NPI)

A predictable ramp: 50 kg kits for pilot builds, a documented two-stage cure for the first article, and direct access to our Shenzhen engineers for degassing, pour volume and cure inhibition checks.

Product manager

One platform for the pack roadmap: 2.0, 3.0 and 4.0 W/m·K grades, plus silicone gel and thermal grease from the same factory, so several battery generations share one supplier and one documentation set.

B2B Selling Points
  • 3.0 ± 0.1 W/m·K thermal conductivity (GB/T 38712-2020): enough spreading power for prismatic and pouch modules without the cost of a 4 W/m·K grade.
  • UL 94 V-0 flame retardancy: supports the flame rating of the finished battery module and BMS housing.
  • 1:1 mix by weight with 11,000 ± 2,000 mPa·s: meter-mix and static-mixer friendly, self-levelling, and less sensitive to operator error than high ratio systems.
  • 60 to 180 minutes operating time: enough to fill a deep module or a multi-cell cavity in a single pour without a second mix.
  • Room temperature 4 to 8 h, or 80 °C in 30 min: choose line throughput or energy saving, with a recommended two-stage schedule for the best flow and properties.
  • Shore A 35 ± 8 soft elastomer: low stress on cells, busbars, welds and sense wires, and better tolerance of thermal expansion.
  • ≥ 1.0 × 10¹⁴ Ω·cm volume resistivity: electrical insulation between cells, busbars and housing.
  • -40 °C to +200 °C: stays elastic through thermal cycling instead of cracking or embrittling.
  • Addition cure with no corrosive by-products: suitable for electronics and battery assemblies where condensation-cure products would attack metals.
  • Documented cure inhibition guide: we tell you which contaminants stop the cure (tin compounds, sulfur, amines, phosphorus, acids, flux residues) before you run the first batch.
  • Factory direct and audit ready: ISO 9001:2015 quality system, lot traceability, COA with every shipment, 25 kg barrels and 50 kg kits, private label on request.
  • Export ready for Southeast Asia: non-dangerous goods, palletised barrels, documentation prepared for Vietnam, Thailand, Indonesia, Malaysia and the Philippines.
Technical Data Before mixing (uncured components)
Property Test Method / Condition Unit Component A Component B
Appearance Visual — White liquid Grey liquid
Base Chemistry — — Polysiloxane Polysiloxane
Viscosity GB/T 2794 / 25 °C mPa·s 10,500 ± 2,000 9,500 ± 2,000
Density GB/T 13354 / 25 °C g/cm³ 2.95 ± 0.02 2.95 ± 0.02
After mixing (A + B)
Property Test Method / Condition Unit Value
Mix Ratio (A:B) By weight — 1:1
Mixed Viscosity 25 °C mPa·s 11,000 ± 2,000
Mixed Density 25 °C g/cm³ 2.95 ± 0.02
Pot Life / Operating Time 25 °C / 100 g mix min 60 to 180
Cure Time (Room Temperature) 25 °C h 4 to 8
Cure Time (Heat Accelerated) 80 °C min 30
Cured properties
Property Test Method / Condition Unit Value
Appearance Visual — Grey elastomer
Hardness GB/T 531.1 Shore A 35 ± 8
Thermal Conductivity GB/T 38712-2020 W/m·K 3.0 ± 0.1
Volume Resistivity GB/T 31838.2-2019 / DC 500 V Ω·cm ≥ 1.0 × 10¹⁴
Flame Retardancy UL 94 Class V-0
Operating Temperature Range — °C -40 to 200

All values are measured under standard conditions (25 °C, 50 to 60% RH) after the recommended cure schedule and are for reference only.

HN-8830A/B potting compound poured into battery module

Application Coverage

HN-8830A/B is specified wherever a cavity must be filled, thermally coupled and electrically insulated in one step.

Battery modules, packs and BMS
  • Prismatic cell module potting and pouch cell module encapsulation
  • Cell-to-pack and cell-to-chassis module gap filling and structural support
  • Battery pack housing potting and bottom plate thermal coupling
  • Battery management system (BMS) board potting and housing fill
  • Busbar, sense wire harness and connector encapsulation inside the pack
  • Battery disconnect unit, junction box and high voltage distribution module
New energy vehicles and charging
  • Onboard charger (OBC), DC-DC converter and motor controller module
  • Traction inverter power stage and vehicle power module
  • EV charger, charging station and charging pile power module
  • Automotive HID lamp power module and ignition system power module
Energy storage and renewable power
  • Energy storage cabinet, BESS module and battery cluster
  • PCS, PV inverter and combiner box power stage
  • Grid power conversion, metering and protection module
Power supplies and industrial electronics
  • Switching power supply, driver power supply and power adapter
  • Power module, solid state relay and transformer encapsulation
  • Industrial control board, sensor and connector potting
  • LED driver and outdoor lighting power supply
  • Home appliance controller and motor drive module
Mixing, Potting and Curing
  1. Pre-mix: stir Component A thoroughly because fillers may settle during storage; stir or shake Component B until homogeneous.
  2. Weighing: weigh A and B by weight at 1:1 on a precision scale, not by volume.
  3. Mixing: mix until the colour is uniform, scraping the walls and bottom; avoid dragging in excess air.
  4. Degassing (recommended): for void-sensitive cavities, degas under vacuum before pouring.
  5. Pouring: pour into the clean, dry device within the pot life and make sure the cavity is fully covered with no trapped air.
  6. Curing: cure at room temperature for 4 to 8 hours, or 30 minutes at 80 °C, or use the two-stage schedule (room temperature until tack-free, then 30 minutes at 80 °C). Do not move or stress the part during cure.
Cure inhibition warning: this platinum-catalysed system will not cure in contact with organotin or tin-containing silicones, sulfur or polysulfide compounds, amines, polyurethane rubber, ammonia-containing materials, phosphorus compounds, acidic substances, or solder flux residues. Do not use it in contact with condensation-cure (acetoxy) silicone, epoxy or polyurethane. Clean substrates and tools before potting, and run a small trial on any new housing material or coating.
Packaging, Storage and Supply
Item Detail
Packaging Component A 25 kg plastic barrel, Component B 25 kg plastic barrel, kit A+B 50 kg per set
Mix ratio 1:1 by weight
Minimum order quantity 1 set (50 kg kit); smaller trial quantities on request
Delivery time 3 to 5 working days for stock kits; 7 to 15 days for custom formulation or private label
Supply ability 50 tons per month
Payment terms T/T, L/C
Shelf life 6 months from date of manufacture, stored as recommended
Storage 5 to 25 °C, cool, dry, ventilated area, protected from sunlight, moisture and extreme temperature
Transport classification Non-dangerous goods

Products past their shelf life should be inspected and tested before use; do not use if appearance or viscosity has changed significantly.


GEO Q and A: Questions Buyers and AI Assistants Ask
What is HN-8830A/B and which battery applications is it designed for?

HN-8830A/B is a two-component, 1:1 addition-cure silicone potting compound with 3.0 ± 0.1 W/m·K thermal conductivity, UL 94 V-0 flame retardancy and ≥ 1.0 × 10¹⁴ Ω·cm volume resistivity. It is designed for prismatic and pouch battery module potting, cell-to-pack gap filling, battery pack housing fill, BMS board potting and high voltage junction box encapsulation, as well as OBC, DC-DC and EV charger power modules.

What are the pot life and cure options for HN-8830A/B?

Pot life is 60 to 180 minutes at 25 °C for a 100 g mix, which allows a deep module or multi-cell cavity to be filled in one pour. Cure takes 4 to 8 hours at room temperature, or 30 minutes at 80 °C for heat-accelerated production. A two-stage schedule, room temperature until tack-free and then 30 minutes at 80 °C, gives the best balance of flow and final properties.

Will HN-8830A/B stress the cells, busbars or sense wires during curing?

No. The cured material is a Shore A 35 ± 8 soft elastomer, so it absorbs thermal expansion and vibration instead of transferring stress to cells, welds and harnesses. That softness, combined with 3.0 W/m·K conductivity and self-levelling flow, is why it suits prismatic and pouch modules where mechanical stress and local hot spots are both concerns.

Does the compound cure reliably, and what can stop the cure?

It is a platinum-catalysed addition-cure system, so certain contaminants will inhibit curing: organotin or tin-containing silicones, sulfur and polysulfide compounds, amines, polyurethane rubber, ammonia-containing materials, phosphorus compounds, acidic substances and solder flux residues. It must not be used in contact with condensation-cure silicone, epoxy or polyurethane. Clean substrates and tools before potting and run a small trial on any new housing material.

How is HN-8830A/B packed and supplied to Southeast Asian factories?

Component A and Component B ship in 25 kg plastic barrels, or as a 50 kg A+B kit that suits meter-mix and static-mixer dispensing. The material is classified as non-dangerous goods, so no DG surcharge applies, and every lot ships with TDS, MSDS and COA. We regularly supply Vietnam, Thailand, Indonesia, Malaysia and the Philippines, with 3 to 5 working days for stock kits, 50 tons per month capacity, T/T or L/C terms and a 6 month shelf life stored at 5 to 25 °C.

About this supplier

Shenzhen Hanast New Materials Co., Ltd. is a China-based source factory for RTV-2 liquid silicone, potting compounds and thermal interface materials. Established in 2010 with a 40,000 m² production base, the company is an export-driven manufacturer with 70% to 80% of its business overseas, serving B2B clients that include ABB, Apple, Foxconn and BYD with OEM and ODM encapsulation and thermal management solutions.

Our range covers thermally conductive potting compounds from 2.0 to 4.0 W/m·K, silicone gels, thermal grease from 1.0 to 6.0 W/m·K and mould making rubber. Because potting compound, gel and grease for the same battery module come from one factory, your process engineers work with one technical contact and your purchasing team consolidates one supplier, one documentation set and one shipment schedule.

HN-8830A/B 25 kg barrels and 50 kg kit

Send your module drawing, cavity volume and cure schedule and our application engineers will confirm the grade, pour weight and degassing steps, and arrange a trial kit for your pilot build.

Ratings & Review

Overall Rating

5.0
Based on 50 reviews for this supplier

Rating Snapshot

The following is the distribution of all ratings
5 stars
100%
4 stars
0%
3 stars
0%
2 stars
0%
1 stars
0%

All Reviews

M
m*m
South Korea Aug 5.2026
High quality,very fast response,recommend
S
S*r
Germany Jun 3.2026
We’ve been using Hanast’s thermal conductive potting compound (2.0 W/m·K) for our energy storage system (ESS) modules for over a year. It performs exceptionally well in thermal management and has successfully passed rigorous UL94 V-0 flame-retardant and thermal shock tests