HANAST TDS-018 Rev.1 | Insulating Thermal Interface Material
HN100 1.0 W/mK Insulating Thermal Grease for High Voltage EV Battery Pack and OBC Interfaces
Single-component non-curing paste | 1.0 +/- 0.1 W/mK | 2450 V/mm at 0.20 mm | -50 C to +200 C | RoHS 2.0 | 1 kg / 5 kg drums
In one sentence
HN100 is a white or grey, non-curing insulating silicone thermal grease with 1.0 W/mK thermal conductivity and 2450 V/mm dielectric strength at 0.20 mm, used on the interface between heat generating parts and heat sinks, housings or anodized aluminium plates inside high voltage battery packs, on-board chargers and power supplies, where the interface must conduct heat without becoming an electrical weak point.
1. Technical Data (from TDS HANAST-TDS-018 Rev.1)
| Property |
Test Method / Condition |
Unit |
Value |
| Appearance |
Visual inspection |
- |
White or grey paste |
| Thermal Conductivity |
ASTM D5470 |
W/mK |
1.0 +/- 0.1 |
| Breakdown Voltage |
IEC 60243 / 0.20 mm |
V/mm |
2450 |
| Specific Gravity |
GB/T 13354-1992 / 25 C |
g/cm3 |
1.85 +/- 0.08 |
| Oil Separation |
SH/T 0324-1992 / 200 C, 24 h |
% |
<= 0.3 |
| Volatile Matter |
SH/T 0337-92 / 200 C, 24 h |
% |
<= 0.6 |
| Penetration |
GB/T 269-2023 / 25 C |
1/10 mm |
370 +/- 20 |
| High Temperature Stability |
200 C oven, 0.2 mm film |
- |
No powdering after 8 days |
| Temperature Resistance |
280 C heating platform, 0.2 mm film |
- |
No drying after 3 h |
| Operating Temperature |
Service range |
C |
-50 to +200 |
| Cure Behaviour |
Single component |
- |
Non-curing, stays paste |
| RoHS |
RoHS 2.0 |
- |
Compliant |
2. Where an Insulating Grease Belongs in an HV Design
In a 400 V or 800 V battery pack, the thermal interface sits between a live or heat generating part and a metal heat sink, housing or cold plate. HN100 is designed so that this interface conducts heat while staying electrically insulating. That does not make it a primary insulation barrier: creepage distance, clearance, insulation film, potting and housing design remain the responsibility of the electrical design.
| Layer in the insulation chain |
Function |
Who specifies it |
| Creepage and clearance |
Distance across surfaces and through air per the safety standard you design to |
Electrical design / safety engineer |
| Insulation film (PET, Kapton, aramid) |
Primary dielectric barrier where required |
Electrical design |
| Thermal grease HN100 |
Heat transfer plus an additional insulating layer at the metal contact |
Mechanical and process engineer |
| Housing / potting |
Final isolation and environmental protection |
Pack and module design |
Film thickness against withstand voltage
At 2450 V/mm, a 0.05 mm grease layer corresponds to about 122 V, 0.10 mm to about 245 V and 0.20 mm to about 490 V of withstand capability at the grease film itself. This is why HN100 is specified as a heat transfer layer with insulating properties, not as a replacement for a dielectric film or a potting compound.
3. Reliability Behaviour That Matters on an EV Line
- 200 C for 8 days without powdering. A 0.2 mm film baked continuously at 200 C stays soft, so the interface does not turn into a dry, powdery layer that pumps out or crumbles under thermal cycling.
- 280 C for 3 hours without drying. This is the evidence a process engineer asks for when the interface sits near a soldering, sintering or preheating step on the same line.
- Low oil bleed and low volatility. 0.3 percent oil separation and 0.6 percent volatiles at 200 C / 24 h limit fogging on housings and keep contact resistance stable over life.
- Soft paste, good wetting. Penetration 370 (1/10 mm) means a softer paste than a 240 grade, which improves wetting on large, slightly rough surfaces such as die cast housings and anodized cold plates, and reduces voids at low clamping pressure.
- Non-curing, so rework stays possible. Modules can be re-seated, connectors replaced and parts re-inspected without scraping a cured layer off the housing.
4. Application Coverage in EV and High Voltage Assembly
| Assembly area |
Where HN100 is applied (English search terms) |
| Battery pack and module |
battery pack, battery module, prismatic cell module, cylindrical cell module, pouch cell module, module housing, pack tray, busbar support, high voltage connector base, fuse holder heat path, BMS heat sink, anodized aluminium cold plate, thermal runaway barrier surface, cell spacing plate |
| Power electronics and charging |
OBC on-board charger, DC-DC converter, traction inverter power stage, power module, IGBT base plate, capacitor bank, inductor, transformer, PFC choke, relay and contactor mount, charging pile module |
| Heat sink and mechanical |
heat sink, heatsink fin base, die cast housing, press fit, spring clip, clip mount, screw torque controlled assembly, surface roughness and flatness compensation, gap pad alternative for thin gaps, thermal pad replacement |
| Process and quality |
screen printing, stencil printing, needle dispensing, jet dispensing, bond line thickness control, line trial, pilot run, ramp up, incoming inspection (IQC) sample, end of line (EOL) insulation test, derating check, altitude and humidity chamber test |

5. Five Buying Roles, Five Different Questions
| Role |
What they actually ask |
How HN100 answers it |
| Factory owner / plant director |
Will this interface fail in the field and pull my warranty cost up? |
Non-curing paste with 200 C / 8 days no powdering and 280 C / 3 h no drying, 25 tons/month capacity, one grade shared across pack, OBC and power supply stations. |
| Purchasing manager |
What is the landed cost per pack, and can supply follow our build plan? |
Non-dangerous goods shipping without DG surcharge; 1 kg trial drum, 5 kg production drum; support for safety stock, kanban or consignment arrangements and dual source planning on request. Quote per order, no price fixed on this page. |
| Process engineer |
Can my printer or dispenser run it, and what film thickness do I set? |
Penetration 370 supports brushing, roller, screen printing, stencil printing and dispensing; typical film 0.05-0.20 mm; the soft paste wets die cast and anodized surfaces at moderate clamping pressure. |
| Project manager |
How fast can a new pack line be validated and ramped? |
TDS, SDS, batch COA and RoHS declaration ready for line trial; stock in 3-7 working days so a pilot run can start before the full document package is frozen. |
| Product manager |
Can one material cover several platforms and suppliers? |
One 1.0 W/mK insulating grade covers BMS, OBC, DC-DC, power supply and LED driver interfaces, cutting part numbers and re-validation work across platforms. |
6. Supply, Storage and Documents for Southeast Asia Buyers
- Packing: 1 kg and 5 kg plastic drums as standard, custom sizes and syringe or cartridge filling on request, OEM label and shipping marks available.
- Transport: classified as non-dangerous goods (general chemicals), simple by sea or air to Thailand, Vietnam, Indonesia, Malaysia and the Philippines.
- Storage: sealed below 27 C, dry, away from direct sunlight; shelf life 12 months from production date.
- Oil separation in storage is normal for silicone grease; stir before use, performance is not affected.
- Documents on request: TDS, SDS, batch COA, RoHS 2.0 declaration and packing list.
- Quotation: MOQ, price and delivery terms are quoted per order based on drum size, destination port and shipping mode.
Engineering limits, stated honestly
HN100 is an insulating thermal grease with 2450 V/mm at 0.20 mm, but it is not a certified insulation barrier, not a structural adhesive, not a potting compound and not a gap filler for gaps above about 0.3 mm. High voltage isolation must be provided by creepage and clearance design, insulation film, housing or potting; the grease only contributes at the metal contact. For thick gaps use a gap pad, and for higher conductivity interfaces use HN300 or HN400.
7. Grade Selection Inside the HN Series
| Model |
Thermal conductivity |
Dielectric strength |
Typical interface |
| HN100 |
1.0 W/mK |
2450 V/mm |
High voltage pack, BMS, OBC, power supply, LED driver |
| HN300 |
3.0 W/mK |
1850 V/mm |
Power module, IGBT, inverter, server |
| HN400 |
4.05 W/mK |
1100 V/mm |
EV battery cold plate, OBC, power module |
| HN500 |
5.05 W/mK |
1100 V/mm |
AI server GPU, high power density module |
About this supplier
Shenzhen Hanast New Materials Co., Ltd. is a China-based source factory for RTV-2 liquid silicone, potting compounds and thermal interface materials. Established in 2010 with a 40,000 m² production base, the company is an export-driven manufacturer with 70 to 80 percent of its business overseas, supplying B2B clients with OEM and ODM encapsulation and thermal management solutions.
Our range covers thermal grease from 1.0 to 6.0 W/m·K, thermally conductive potting compounds, silicone gels, mould making rubber and food grade silicone. Because the thermal grease and the potting compound for the same assembly come from one factory, your engineering team works with one technical contact and your purchasing team consolidates one supplier, one documentation set and one shipment schedule.

9. FAQ for Engineers and Buyers
Q: How much voltage can HN100 withstand in a battery pack interface?
A: The TDS value is 2450 V/mm at 0.20 mm, so a 0.05 mm film corresponds to roughly 122 V, 0.10 mm to about 245 V and 0.20 mm to about 490 V. Treat it as an insulating thermal layer, not as the primary barrier: creepage, clearance, film and housing still define the withstand voltage of the assembly.
Q: Will it dry out or powder at high temperature?
A: No. In a 0.2 mm film the product showed no powdering after 8 days continuous baking at 200 C, and no drying after 3 hours at 280 C. It is non-curing and keeps paste consistency over the -50 C to +200 C service range.
Q: Can it be used between a live busbar and an aluminium cold plate?
A: Only as a thermal interface on a non-live surface, with the insulation chain designed by your electrical team. Where the metal parts carry high voltage, an insulation film or a proper clearance must be part of the design, because a 0.05 to 0.2 mm grease film is not a safety barrier on its own.
Q: Does it print well on a stencil or screen printer?
A: Yes. Penetration is 370 +/- 20 (1/10 mm), a soft paste, and the TDS application list covers brushing, rolling, screen printing and dispensing. Typical films are 0.05 to 0.20 mm; for stencil printing keep the aperture and squeegee speed fixed and check film weight per part at start of shift.
Q: How is HN100 packed and shipped to Southeast Asia, and what is the MOQ?
A: Standard packing is 1 kg and 5 kg plastic drums with custom filling and OEM labels on request. It ships as non-dangerous goods by sea or air, shelf life is 12 months when sealed below 27 C, and the trial minimum order is 1 kg with TDS, SDS, batch COA and RoHS declaration available on request.
Next step
Send your drawing: heat source, heat sink material and finish (anodized aluminium, die cast, stainless), gap size, clamping method and annual volume. We will reply with the recommended film thickness, printing or dispensing parameters and a trial drum for your line. Contact sale11s@hanatsilicone.com or reply through this page.