HANAST TDS-018 Rev.1 | Two and Three Wheeler Thermal Interface
HN100 1.0 W/mK Insulating Thermal Grease for E-Motorcycle Battery Packs and Battery Swap Cabinets
48 V / 60 V / 72 V platforms | 1.0 +/- 0.1 W/mK | 2450 V/mm at 0.20 mm | -50 C to +200 C | RoHS 2.0 | 1 kg / 5 kg drums
In one sentence
HN100 is a white or grey, non-curing insulating silicone thermal grease with 1.0 W/mK and 2450 V/mm at 0.20 mm, used between MOSFETs, controllers, hub motors, BMS boards and battery packs of 48 V to 72 V e-motorcycles and three-wheelers, and inside battery swap cabinets and charger modules, where a thin heat transfer layer must stay electrically insulating.
| Property | Test Method / Condition | Unit | Value |
|---|---|---|---|
| Appearance | Visual inspection | - | White or grey paste |
| Thermal Conductivity | ASTM D5470 | W/mK | 1.0 +/- 0.1 |
| Breakdown Voltage | IEC 60243 / 0.20 mm | V/mm | 2450 |
| Specific Gravity | GB/T 13354-1992 / 25 C | g/cm3 | 1.85 +/- 0.08 |
| Oil Separation | SH/T 0324-1992 / 200 C, 24 h | % | <= 0.3 |
| Volatile Matter | SH/T 0337-92 / 200 C, 24 h | % | <= 0.6 |
| Penetration | GB/T 269-2023 / 25 C | 1/10 mm | 370 +/- 20 |
| High Temperature Stability | 200 C oven, 0.2 mm film | - | No powdering after 8 days |
| Temperature Resistance | 280 C heating platform, 0.2 mm film | - | No drying after 3 h |
| Operating Temperature | Service range | C | -50 to +200 |
| Cure Behaviour | Single component | - | Non-curing, stays paste |
| RoHS | RoHS 2.0 | - | Compliant |
A two-wheeler pack runs at 48 V, 60 V or 72 V, far below the 400 V and 800 V car platforms, so the insulation requirement is different: the design is usually dominated by cost, weight and repairability rather than by kilovolt clearance. That is exactly where HN100 fits. It gives 1.0 W/mK heat transfer with 2450 V/mm dielectric strength, which leaves a comfortable margin over a 72 V system while keeping the paste soft enough to be applied by hand, by screen printing or by a small dispenser in a high mix, low volume plant.
| Platform | System voltage | What the interface needs | Fitting grade |
|---|---|---|---|
| E-motorcycle / e-scooter pack | 48 V / 60 V / 72 V | Insulation margin, low cost, easy rework | HN100 |
| Three-wheeler and cargo trike | 60 V / 72 V | Larger controller and motor housing area, thicker film tolerance | HN100 |
| Battery swap cabinet | 48-72 V per slot, AC input side | Insulation plus long service life in hot cabinet | HN100 |
| Passenger EV traction module | 400 V / 800 V | Higher conductivity and a full insulation chain | HN400 with film |
| Assembly area | Where HN100 is applied (English search terms) |
|---|---|
| Electric two and three wheelers | e-motorcycle, e-scooter, moped, e-bike, electric bicycle, three-wheeler, cargo trike, tuk tuk, e-rickshaw, low speed EV, delivery scooter, fleet scooter |
| Powertrain and electronics | hub motor, mid-drive motor, FOC controller, motor controller MOSFET, BMS board, battery pack 48 V, 60 V and 72 V, charger, DC-DC converter, dashboard display, LED headlight, horn and relay module |
| Swap and charging infrastructure | battery swap station, swap cabinet, charging cabinet, charging rack, charger power module, connector base, contactor mount, precharge resistor, discharge resistor, busbar joint |
| Industrial and light electric vehicles | AGV, AMR, forklift, pallet truck, golf cart, floor scrubber, warehouse trolley, drive controller |
| Production and quality | die cast housing, aluminium extrusion heat sink, pin fin heat sink, press fit, spring clip, screw torque controlled assembly, film thickness check, stencil printing, dispensing line, IQC sample, end of line test |
| Role | What they actually ask | How HN100 answers it |
|---|---|---|
| Factory owner / plant director | What does it cost per unit, and will it come back as a field failure? | 1.0 W/mK paste in a 1 kg drum covers thousands of controllers; 200 C / 8 days no powdering and non-curing behaviour avoid the dried-out interface that comes back as warranty. |
| Purchasing manager | Can I buy small quantities first, and does it ship as dangerous goods? | 1 kg trial drum, 5 kg production drum, non-dangerous goods classification without DG surcharge, 25 tons per month capacity, quote per order without a fixed price on this page. |
| Process engineer | Can my operators apply it consistently, and what film thickness? | Penetration 370 is a soft paste for brush, roller, screen printing and small dispensers; target 0.05-0.10 mm on controllers and 0.10-0.20 mm on cast housings, with torque control after assembly. |
| Project manager | How fast can we go from sample to mass production for a new model? | Stock in 3-7 working days, TDS, SDS, batch COA and RoHS declaration ready, so a pilot batch can be built while tooling for the new model is still in progress. |
| Product manager | Can the same material serve several models and suppliers? | One insulating grade covers controller, motor housing, BMS, charger and cabinet interfaces across 48 V, 60 V and 72 V models, which reduces part numbers and re-validation. |
Engineering limits, stated honestly
HN100 is an insulating thermal grease with 2450 V/mm at 0.20 mm, but it is not a certified insulation barrier, not a structural adhesive, not a potting compound and not a gap filler for gaps above about 0.3 mm. Insulation coordination still comes from creepage and clearance, insulation film, housing or potting. For a 400 V or 800 V traction module use HN400 together with a proper insulation chain, and for thick gaps use a gap pad.
| Model | Thermal conductivity | Dielectric strength | Typical interface |
|---|---|---|---|
| HN100 | 1.0 W/mK | 2450 V/mm | E-motorcycle pack, controller, BMS, swap cabinet, power supply |
| HN300 | 3.0 W/mK | 1850 V/mm | Power module, IGBT, inverter, server |
| HN400 | 4.05 W/mK | 1100 V/mm | EV battery cold plate, OBC, traction power module |
| HN500 | 5.05 W/mK | 1100 V/mm | AI server GPU, high power density module |
About this supplier
Shenzhen Hanast New Materials Co., Ltd. is a China-based source factory for RTV-2 liquid silicone, potting compounds and thermal interface materials. Established in 2010 with a 40,000 m² production base, the company is an export-driven manufacturer with 70 to 80 percent of its business overseas, supplying B2B clients with OEM and ODM encapsulation and thermal management solutions.
Our range covers thermal grease from 1.0 to 6.0 W/m·K, thermally conductive potting compounds, silicone gels, mould making rubber and food grade silicone. Because the thermal grease and the potting compound for the same assembly come from one factory, your engineering team works with one technical contact and your purchasing team consolidates one supplier, one documentation set and one shipment schedule.
![]()
Q: Is a 1.0 W/mK grease enough for a 72 V e-motorcycle controller?
A: For most 48 to 72 V controllers, yes. The controller housing area and the film thickness matter more than the last 1 W/mK: moving from a 1 mm pad to a 0.05 mm paste film reduces the interface resistance by an order of magnitude. If the model uses a very high current controller with a small housing, HN300 at 3.0 W/mK is the next step.
Q: Why choose an insulating grade instead of a cheaper non-insulating paste?
A: Because the interface sits close to live MOSFET tabs, busbars and motor windings, and because maintenance staff may re-open the housing in the field. 2450 V/mm at 0.20 mm keeps a wide margin over a 72 V system while still transferring heat, at a cost close to a standard grease.
Q: Can HN100 be used inside a battery swap cabinet?
A: Yes, on the charger module, contactor mount, precharge and discharge resistor interfaces and the busbar joints inside the cabinet. The cabinet runs hot, so the 200 C / 8 days no powdering and 280 C / 3 h no drying data are the relevant points, together with the non-curing behaviour that keeps the interface serviceable.
Q: How is it applied on a small assembly line?
A: Brush, roller, screen printing, stencil printing or a small pneumatic dispenser all work. Keep the film at 0.05 to 0.10 mm on flat controller plates and 0.10 to 0.20 mm on cast surfaces, check film weight at the start of each shift, and torque the screws to the drawing value immediately after assembly.
Q: How is HN100 packed and shipped to Southeast Asia, and what is the MOQ?
A: Standard packing is 1 kg and 5 kg plastic drums with custom filling and OEM labels on request. It ships as non-dangerous goods by sea or air, shelf life is 12 months when sealed below 27 C, and the trial minimum order is 1 kg with TDS, SDS, batch COA and RoHS declaration available on request.
Next step
Tell us the model: system voltage, controller or motor housing material and finish, gap size, annual volume and whether the part is serviced in the field. We will reply with the recommended film thickness, application method and a trial drum for your pilot batch. Contact sale11s@hanatsilicone.com or reply through this page.